Netgear Switch M4100-12G-POE+ User Manual Page 399
- Page / 768
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
IPv6 Commands
399
ProSafe M4100 and M7100 Managed Switches
Note: Some of the information below displays only if you enable OSPF
and configure certain features.
Term Definition
Router ID
A 32-bit integer in dotted decimal format identifying the router, about which information is
displayed. This is a configured value.
OSPF Admin
Mode
Shows whether the administrative mode of OSPF in the router is enabled or disabled.
This is a configured value.
ABR Status
Shows whether the router is an OSPF Area Border Router.
ASBR Status
Reflects whether the ASBR mode is enabled or disabled. Enable implies that the router
is an autonomous system border router. Router automatically becomes an ASBR when it
is configured to redistribute routes learnt from other protocol. The possible values for the
ASBR status are enabled (if the router is configured to redistribute routes learned by
other protocols) or disabled (if the router is not configured for the same).
Stub Router
When OSPF runs out of resources to store the entire link state database, or any other
state information, OSPF goes into stub router mode. As a stub router, OSPF reoriginates
its own router LSAs, setting the cost of all nonstub interfaces to infinity. To restore OSPF
to normal operation, disable and reenable OSPF.
Exit Overflow
Interval
The number of seconds that, after entering overflow state, a router will attempt to leave
overflow state.
External LSDB
Overflow
When the number of non-default external LSAs exceeds the configured limit, External
LSDB Limit, OSPF goes into LSDB overflow state. In this state, OSPF withdraws all of its
self-originated non-default external LSAs. After the Exit Overflow Interval, OSPF leaves
the overflow state, if the number of external LSAs has been reduced.
External LSA
Count
The number of external (LS type 5) link-state advertisements in the link-state database.
External LSA
Checksum
The sum of the LS checksums of external link-state advertisements contained in the
link-state database.
New LSAs
Originated
The number of new link-state advertisements that have been originated.
LSAs Received
The number of link-state advertisements received determined to be new instantiations.
LSA Count
The total number of link state advertisements currently in the link state database.
Maximum
Number of
LSAs
The maximum number of LSAs that OSPF can store.
LSA High Water
Mark
The maximum size of the link state database since the system started.
Retransmit List
Entries
The total number of LSAs waiting to be acknowledged by all neighbors. An LSA might be
pending acknowledgment from more than one neighbor.
- ProSafe Managed Switch 1
- Trademarks 2
- Revision History 2
- Contents 3
- Chapter 4 Routing Commands 4
- Chapter 6 IPv6 Commands 5
- Chapter 10 Utility Commands 5
- Chapter 12 Log Messages 6
- Chapter 14 Command List 6
- Licensing and Command Support 8
- Command Syntax 9
- Command Conventions 9
- Common Parameter Values 10
- Slot/Port Naming Convention 11
- Using a Command’s “No” Form 12
- Managed Switch Modules 12
- Command Modes 12
- Table 5. CLI Command Modes 13
- CLI Error Messages 16
- CLI Line-Editing Conventions 17
- Using CLI Help 17
- Accessing the CLI 18
- Port Configuration Commands 21
- Loopback Interface Commands 27
- VLAN Commands 47
- Double VLAN Commands 60
- Voice VLAN Commands 63
- Protected Ports Commands 65
- Private VLAN 68
- GARP Commands 71
- GVRP Commands 73
- GMRP Commands 75
- 802.1X Supplicant Commands 91
- Storm-Control Commands 94
- Switching Commands 100
- Flow Control Commands 104
- Port Mirroring 121
- Static MAC Filtering 123
- DHCP L2 Relay Agent Commands 127
- DHCP Client Commands 131
- MLD Snooping Commands 161
- vlanid 0-3600 165
- Port Security Commands 171
- LLDP (802.1AB) Commands 175
- {<slot/port> 180
- LLDP-MED Commands 184
- Denial of Service Commands 193
- TCP Header Of 194
- • TCP SYN: 194
- MAC Database Commands 203
- ISDP Commands 205
- • About MVR 213
- • MVR Commands 213
- About MVR 214
- MVR Commands 214
- Example: 219
- Routing Commands 221
- IP Routing Commands 227
- Virtual LAN Routing Commands 248
- DHCP and BOOTP Relay Commands 257
- IP Helper Commands 259
- 1583compatibility 264
- Table 1. Trapflags Groups 286
- Dampening 309
- ICMP Throttling Commands 318
- IP Multicast Commands 321
- IP Multicast Commands 322
- DVMRP Commands 326
- PIM Commands 331
- Example 1: 339
- Example 2: 339
- Privileged EXEC 340
- Example 3: 341
- Example 4: 341
- IGMP Proxy Commands 349
- IPv6 Commands 355
- Tunnel Interface Commands 356
- IPv6 Routing Commands 357
- 3ffe:1::1234/64 359
- C - connected, S - static 371
- ::0) and unsupported 376
- OSPFv3 Commands 380
- DHCPv6 Commands 413
- FF02::1:2) 414
- <pool-name> 419
- [<ipv6-address>] 419
- IPv6 Multicast Commands 421
- IPv6 PIM Commands 424
- IPv6 MLD Commands 431
- IPv6 MLD-Proxy Commands 437
- [<slot/port>] 448
- DiffServ Class Commands 452
- Global Config 453
- DiffServ Policy Commands 461
- DiffServ Service Commands 466
- DiffServ Show Commands 468
- <slot/port> [in 471
- [in 471
- {deny 474
- {deny 480
- {deny 485
- [end time date] 489
- AutoVOIP 490
- About PoE 501
- PoE Commands 502
- Format poe reset 506
- Mode Global Config 506
- Interface Config 506
- Mode Interface Config 506
- PSE-capable ports 510
- Utility Commands 512
- Auto Install Commands 513
- Dual Image Commands 515
- Logging Commands 534
- For example: 561
- For each configured server: 563
- DHCP Server Commands 564
- DNS Client Commands 575
- Packet Capture Commands 580
- Cable Test Command 603
- [<index>] 608
- Software License Commands 609
- IP Address Conflict Commands 610
- RFC 2819 612
- RFC 3273 613
- RFC 3434 613
- UDLD Commands 618
- USB commands 620
- Management Commands 623
- Network Interface Commands 626
- “Interface Status” as “Up” 628
- Console Port Access Commands 629
- Telnet Commands 631
- Secure Shell (SSH) Commands 636
- Management Security Commands 639
- Access Commands 647
- User Account Commands 647
- SNMP Commands 670
- RADIUS Commands 680
- TACACS+ Commands 693
- <ip-address 694
- <priority> 697
- IPv6 Management Commands 703
- Log Messages 708
- Table 3. BSP Log Messages 709
- Table 4. NIM Log Messages 709
- Utilities 711
- Management 713
- Table 16. WEB Log Messages 715
- Table 18. SSHD Log Messages 715
- Table 19. SSLT Log Messages 716
- Switching 717
- Table 28. FDB Log Message 721
- Table 31. MFDB Log Message 721
- Table 36. ACL Log Messages 723
- Table 37. CoS Log Message 723
- Routing/IPv6 Routing 724
- Table 43. VRRP Log Messages 726
- Table 44. ARP Log Message 726
- Multicast 727
- Stacking 729
- Technologies 730
- O/S Support 732
- Green Ethernet Commands 734
- Energy-Detect Mode 735
- Table 58 740
- Command List 744
Related products and manuals for Networking Netgear Switch M4100-12G-POE+
Networking Netgear DG834Gv5 User Manual
(44 pages)
(44 pages)
Networking Netgear GA311 User Manual
(52 pages)
(52 pages)
Networking Netgear WNA1000 User's Guide
(58 pages)
(58 pages)
Networking Netgear WNDAP330 User Manual
(7 pages)
(7 pages)
Networking Netgear RH340 User Manual
(6 pages)
(6 pages)
Networking Netgear WMS5316 User Manual
(70 pages)
(70 pages)
Networking Netgear DG834 V3 User Manual
(168 pages)
(168 pages)
Networking Netgear GA302T User Manual
(62 pages)
(62 pages)
Networking Netgear WC7600 User Manual
(307 pages)
(307 pages)
Networking Netgear WG111T User Manual
(49 pages)
(49 pages)
Networking Netgear 597E User's Guide
(49 pages)
(49 pages)
Networking Netgear WG511T User's Guide
(48 pages)
(48 pages)
Networking Netgear 597E User's Guide
(12 pages)
(12 pages)
Networking Netgear WC7520 User Manual
(213 pages)
(213 pages)
Networking Netgear DG834GSP User Manual
(32 pages)
(32 pages)
Networking Netgear ProSafe FS728TP User Manual
(248 pages)
(248 pages)
Networking Netgear 3G User Manual
(106 pages)
(106 pages)
© 2020, manymanuals.com. All rights reserved. | 0.729 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals