Netgear WNDAP360 User Manual Page 10
- Page / 137
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Introduction
10
ProSafe Dual Band Wireless-N Access Point WNDAP360
• Power over Ethernet. Power can be supplied to the wireless access point over the
Ethernet port from any 802.3af-compliant midspan or end-span source.
• Autose
nsing Ethernet connection with Auto Uplink™ interface. Connects to
10/100/1000 Mbps IEEE 802.3 Ethernet networks.
• LED indi
cators. Power/Test, Active, LAN, and WLAN for each radio mode are easily
identified.
• W
i-FI Multimedia (WMM) support. WMM is a subset of the 802.11e standard. WMM
allows wireless traffic to have a range of priorities, depending on the kind of data.
Time-dependent information, like video or audio, has a higher priority than normal traffic.
For WMM to function correctly, wireless clients also need to support WMM.
• Quality
of Service (QoS) support. You can configure parameters that affect traffic
flowing from the wireless access point to the client station and traffic flowing from the
client station to the wireless access point. The QoS feature allows you to prioritize traffic,
such as voice and video traffic, so that packets do not get dropped.
• VLAN security
profiles. Each security profile is automatically allocated a VLAN ID when
the security profile is modified.
802.11b/g/n and 802.11a/n Standards–Based Wireless
Networking
The ProSafe Dual Band Wireless-N Access Point WNDAP360 provides a bridge between
wired Ethernet LANs and 802.11b/g/n and 802.11a/n-compatible wireless LAN networks. It
provides connectivity between wired Ethernet networks and radio-equipped wireless
notebook systems, desktop systems, print servers, and other devices. Additionally, the
wireless access point supports the following wireless features:
• Aggre
gation support
• Redu
ced InterFrame spacing support
• Multiple input
, multiple output (MIMO) support
• Distribu
ted coordinated function (CSMA/CA, back-off procedure, ACK procedure,
retransmission of unacknowledged frames)
• R
TS/CTS handshake
• Beacon g
eneration
• Packet
fragmentation and reassembly
• Auto
or long preamble
• Roaming
among wireless access points on the same subnet
Autosensing Ethernet Connections with Auto Uplink
The ProSafe Dual Band Wireless-N Access Point WNDAP360 can connect to a standard
Ethernet network. The LAN interface is autosensing and capable of full-duplex or half-duplex
operation.
- ProSafe Dual Band 1
- Wireless-N Access Point 1
- WNDAP360 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Contents 3
- Chapter 4 Management 4
- Chapter 6 Troubleshooting 4
- Introduction 6
- What Is In the Box? 7
- System Requirements 7
- Key Features and Standards 8
- Key Features 9
- Networking 10
- Hardware Description 11
- Rear Panel 12
- Figure 3 13
- Ethernet Cabling Requirements 15
- Figure 4 16
- Web Management Interface 18
- Figure 8 19
- To configure time settings: 20
- 3. Click Apply 20
- to save your settings 20
- To configure the IP settings: 21
- 1. Select Con 21
- Figure 11 22
- Figure 12 24
- Figure 13 27
- Ceiling Installation 31
- 5. Connect th 32
- Wall Installation 33
- 4. Connect th 34
- Desk Installation 35
- Figure 14 37
- Security Profiles 38
- Figure 15 42
- Figure 16 42
- Figure 17 43
- Figure 18 47
- Figure 19 47
- Configure Legacy 802.1X 48
- Figure 21 49
- Figure 22 49
- Figure 23 49
- Figure 24 50
- Figure 25 50
- Figure 26 50
- Figure 27 52
- Figure 28 54
- Figure 29 55
- Field Description 56
- Figure 30 57
- Management 58
- SNMP Management 59
- Figure 32 60
- Figure 33 61
- Web Browser Upgrade Procedure 62
- TFTP Server Upgrade Procedure 63
- Defaults 64
- Restore the Configuration 65
- Settings 66
- Default Configuration 67
- Figure 40 68
- Enable the Syslog Server 69
- View System Information 70
- Monitor Wireless Stations 72
- Figure 43 73
- Figure 44 73
- View the Activity Log 75
- Traffic Statistics 75
- Statistics screen: 76
- Figure 47 78
- Figure 48 79
- To configure STP and VLANs: 82
- Figure 49 82
- Hotspot Settings 83
- Figure 51 84
- To configure advanced QoS: 87
- Figure 52 87
- Table 25. EDCA Settings 88
- Configure Wireless Bridging 89
- Wireless PC card 90
- Figure 54 91
- Figure 55 91
- Figure 58 95
- Figure 59 98
- Figure 60 99
- Figure 61 100
- Advanced Configuration 101
- Troubleshooting 103
- Basic Functioning 104
- Wireless-Capable Computer 105
- Request timed out 107
- Problems with Date and Time 108
- Use the Packet Capture Tool 109
- Supplemental Information 110
- Factory Default Settings 112
- Command-Line Reference 115
- Notification of Compliance 128
- FCC Information to User 130
- FCC Declaration of Conformity 130
- FCC Caution 130
- Industry Canada 131
- Industrie Canada 131
- Numerics 132
Related products and manuals for WLAN access points Netgear WNDAP360
WLAN access points Netgear DG834G User Manual
(166 pages)
(166 pages)
WLAN access points Netgear WG102 User Manual
(134 pages)
(134 pages)
WLAN access points Netgear WNDAP330 User's Guide
(142 pages)
(142 pages)
© 2020, manymanuals.com. All rights reserved. | 1.850 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals