Netgear WNDAP360 User Manual Page 102
- Page / 137
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Advanced Configuration
102
ProSafe Dual Band Wireless-N Access Point WNDAP360
3. Activate repeater mode on the wireless access point (AP2 in Figure 59 on page 98):
a. On
the Bridging screen, select the Enable Wireless Bridging check box.
b. Select the W
ireless Point-to-Multi-Point Bridge radio button.
c. Clear the Enable W
ireless Client Association check box to disable wireless client
association (see the red circle in Figure 60 on p
age 99).
Note: If you do not clear the Enable Wireless Client Association check box,
the wireless access point functions in regular point-to-multipoint
bridge mode.
d. If the correct profile names and security options are displayed in the table, select the
check boxes in the Enable column for all security profiles that you want to enable.
e. Click Apply in the Brid
ging screen to activate your repeater settings.
4. Configu
re AP1 on LAN Segment 1 (see Figure 59 on page 98) in repeater mode with the
remote MAC address of AP2.
5. Configu
re AP3 on LAN Segment 3 (see Figure 59 on page 98) in repeater mode with the
remote MAC address of AP2.
6. V
erify the following for all wireless access points:
• All APs
need to be on the same LAN, that is, the LAN IP addresses of all APs need to
be in the same network as the LAN devices.
• If you use DHCP
, all wireless access points need to obtain an IP address
automatically (as a DHCP client). For more information, see Configure IP Settings
and Optional DHCP Server Settings o
n page 21.
• All wireless access points
need to use the same channel, authentication mode, and
security settings.
7. V
erify connectivity across the LANs:
• A compu
ter on any LAN segment should be able to connect to the Internet or share
files and printers with any other PCs or servers connected to any of the two LAN
segments.
Note: You can extend repetition of the wireless signal by adding up to two
more wireless access points that are configured in
point-to-multipoint bridge mode without client association. Also, you
can extend the range of the wireless network with NETGEAR
wireless antenna accessories.
- ProSafe Dual Band 1
- Wireless-N Access Point 1
- WNDAP360 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Contents 3
- Chapter 4 Management 4
- Chapter 6 Troubleshooting 4
- Introduction 6
- What Is In the Box? 7
- System Requirements 7
- Key Features and Standards 8
- Key Features 9
- Networking 10
- Hardware Description 11
- Rear Panel 12
- Figure 3 13
- Ethernet Cabling Requirements 15
- Figure 4 16
- Web Management Interface 18
- Figure 8 19
- To configure time settings: 20
- 3. Click Apply 20
- to save your settings 20
- To configure the IP settings: 21
- 1. Select Con 21
- Figure 11 22
- Figure 12 24
- Figure 13 27
- Ceiling Installation 31
- 5. Connect th 32
- Wall Installation 33
- 4. Connect th 34
- Desk Installation 35
- Figure 14 37
- Security Profiles 38
- Figure 15 42
- Figure 16 42
- Figure 17 43
- Figure 18 47
- Figure 19 47
- Configure Legacy 802.1X 48
- Figure 21 49
- Figure 22 49
- Figure 23 49
- Figure 24 50
- Figure 25 50
- Figure 26 50
- Figure 27 52
- Figure 28 54
- Figure 29 55
- Field Description 56
- Figure 30 57
- Management 58
- SNMP Management 59
- Figure 32 60
- Figure 33 61
- Web Browser Upgrade Procedure 62
- TFTP Server Upgrade Procedure 63
- Defaults 64
- Restore the Configuration 65
- Settings 66
- Default Configuration 67
- Figure 40 68
- Enable the Syslog Server 69
- View System Information 70
- Monitor Wireless Stations 72
- Figure 43 73
- Figure 44 73
- View the Activity Log 75
- Traffic Statistics 75
- Statistics screen: 76
- Figure 47 78
- Figure 48 79
- To configure STP and VLANs: 82
- Figure 49 82
- Hotspot Settings 83
- Figure 51 84
- To configure advanced QoS: 87
- Figure 52 87
- Table 25. EDCA Settings 88
- Configure Wireless Bridging 89
- Wireless PC card 90
- Figure 54 91
- Figure 55 91
- Figure 58 95
- Figure 59 98
- Figure 60 99
- Figure 61 100
- Advanced Configuration 101
- Troubleshooting 103
- Basic Functioning 104
- Wireless-Capable Computer 105
- Request timed out 107
- Problems with Date and Time 108
- Use the Packet Capture Tool 109
- Supplemental Information 110
- Factory Default Settings 112
- Command-Line Reference 115
- Notification of Compliance 128
- FCC Information to User 130
- FCC Declaration of Conformity 130
- FCC Caution 130
- Industry Canada 131
- Industrie Canada 131
- Numerics 132
Related products and manuals for WLAN access points Netgear WNDAP360
WLAN access points Netgear DG834G User Manual
(166 pages)
(166 pages)
WLAN access points Netgear WG102 User Manual
(134 pages)
(134 pages)
WLAN access points Netgear WNDAP330 User's Guide
(142 pages)
(142 pages)
© 2020, manymanuals.com. All rights reserved. | 0.179 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals