Netgear WNDAP360 User Manual Page 135
- Page / 137
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
135
ProSafe Dual Band Wireless-N Access Point WNDAP360
physical specifications 112
pinging wireless access point 106, 107
placement, wireless equipment 14
PoE (Power over Ethernet)
10, 17
point-to-multipoint bridge
regular mode
93
repeating wireless signal 98
point-to-point bridge
90
policy, access control
46
port and connectors, rear panel 12
ports
RADIUS servers
52
SNMP manager, traps
59
syslog server 69
power adapter specifications
112
Power/Test LED
behavior
17
description 12
troubleshooting
104
powersaving, WMM 57
preamble type
86
pre-shared key (PSK), WPA,
WPA2, and mixed mode
38, 51
priority queues
advanced QoS
87
WMM QoS 56
profiles, security
creating and configuring
42–46
description
38
protection spacing (11ng only) 25
PSK (pre-shared key), WPA, WPA2, and mixed mode
38, 51
Q
QoS (Quality of Service)
advanced
86
WMM
56
R
radio
scheduling to turn off
55
turning off, 2.4 GHz 24
turning off, 5 GHz
27
RADIUS servers, configuring
51
range guidelines, wireless equipment
14
read-only name, read-write name, SNMP
59
rear panel
12
reauthentication time, RADIUS servers
53
rebooting from web management interface 67
received signal strength indicator (RSSI)
74
redirecting HTTP requests
83
Reduced Interframe Space (RIFS) transmission
85
remote devices, troubleshooting 108
remote MAC addresses
54
remote management, options
58
Request to Send (RTS) threshold 85
Reset button
13, 67, 112
restoring
factory defaults
66
password 68
settings, from saved file
65
restricting access by MAC address 37
RIFS (Reduced Interframe Space) transmission
85
roaming
39
rogue access points, detection of
77
RSSI (received signal strength indicator) 74
RTS (Request to Send) threshold
85
Rx sequence
74
S
Secure Shell (SSH), enabling 60
security lock
13
security profiles
creating and configuring
42–46
description 38
security, wireless options
36
separating wireless clients
39, 46
servers, configuring
DHCP
22
DNS 21–23
hotspot 83
NTP
20
RADIUS 51
syslog 69
service set identifiers. See SSIDs.
shared key, WEP
45, 47
shared secrets, RADIUS servers 52
show configuration CLI command
61
signal-to-noise ratio (SNR)
74
SMA connectors, external antennas
13
SNMP (Simple Network Management Protocol),
co
nfiguring
59
software
backing up
64
factory defaults
66
restoring from saved file 65
upgrading
62
version, viewing
71
Spanning Tree Protocol (STP), enabling 82
specifications, technical
110
- ProSafe Dual Band 1
- Wireless-N Access Point 1
- WNDAP360 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Contents 3
- Chapter 4 Management 4
- Chapter 6 Troubleshooting 4
- Introduction 6
- What Is In the Box? 7
- System Requirements 7
- Key Features and Standards 8
- Key Features 9
- Networking 10
- Hardware Description 11
- Rear Panel 12
- Figure 3 13
- Ethernet Cabling Requirements 15
- Figure 4 16
- Web Management Interface 18
- Figure 8 19
- To configure time settings: 20
- 3. Click Apply 20
- to save your settings 20
- To configure the IP settings: 21
- 1. Select Con 21
- Figure 11 22
- Figure 12 24
- Figure 13 27
- Ceiling Installation 31
- 5. Connect th 32
- Wall Installation 33
- 4. Connect th 34
- Desk Installation 35
- Figure 14 37
- Security Profiles 38
- Figure 15 42
- Figure 16 42
- Figure 17 43
- Figure 18 47
- Figure 19 47
- Configure Legacy 802.1X 48
- Figure 21 49
- Figure 22 49
- Figure 23 49
- Figure 24 50
- Figure 25 50
- Figure 26 50
- Figure 27 52
- Figure 28 54
- Figure 29 55
- Field Description 56
- Figure 30 57
- Management 58
- SNMP Management 59
- Figure 32 60
- Figure 33 61
- Web Browser Upgrade Procedure 62
- TFTP Server Upgrade Procedure 63
- Defaults 64
- Restore the Configuration 65
- Settings 66
- Default Configuration 67
- Figure 40 68
- Enable the Syslog Server 69
- View System Information 70
- Monitor Wireless Stations 72
- Figure 43 73
- Figure 44 73
- View the Activity Log 75
- Traffic Statistics 75
- Statistics screen: 76
- Figure 47 78
- Figure 48 79
- To configure STP and VLANs: 82
- Figure 49 82
- Hotspot Settings 83
- Figure 51 84
- To configure advanced QoS: 87
- Figure 52 87
- Table 25. EDCA Settings 88
- Configure Wireless Bridging 89
- Wireless PC card 90
- Figure 54 91
- Figure 55 91
- Figure 58 95
- Figure 59 98
- Figure 60 99
- Figure 61 100
- Advanced Configuration 101
- Troubleshooting 103
- Basic Functioning 104
- Wireless-Capable Computer 105
- Request timed out 107
- Problems with Date and Time 108
- Use the Packet Capture Tool 109
- Supplemental Information 110
- Factory Default Settings 112
- Command-Line Reference 115
- Notification of Compliance 128
- FCC Information to User 130
- FCC Declaration of Conformity 130
- FCC Caution 130
- Industry Canada 131
- Industrie Canada 131
- Numerics 132
Related products and manuals for WLAN access points Netgear WNDAP360
WLAN access points Netgear DG834G User Manual
(166 pages)
(166 pages)
WLAN access points Netgear WG102 User Manual
(134 pages)
(134 pages)
WLAN access points Netgear WNDAP330 User's Guide
(142 pages)
(142 pages)
© 2020, manymanuals.com. All rights reserved. | 0.823 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals