Netgear WNDAP360 User Manual Page 46
- Page / 137
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Wireless Configuration and Security
46
ProSafe Dual Band Wireless-N Access Point WNDAP360
6. Click Apply to save your settings.
Wireless Client Security
Separation
If you enable wireless client security separation by selecting Enable from the
drop-down list, the associated wireless clients are not be able to communicate
with each other. By default, Disable is selected from the drop-down list. This
feature is intended for hotspots and other public access situations.
Dynamic VLAN From the drop-down list, select how VLANs
operate by making one of the
following selections:
• Dis
able. Disables dynamic VLANs, and enables static VLANs. This is the
default setting.
• Op
tional. Enables dynamic VLANs but if a RADIUS server does not return a
VLAN ID, the wireless station is still allowed to connect to the wireless access
point.
• Require
d. Enables dynamic VLANs. If a RADIUS server does not return a
VLAN ID, the wireless station is not authenticated and cannot connect to the
wireless access point.
For dynamic VLANs to operate (that is, the sele
ction is Optional or Required),
the following is required:
• The hubs and switches on your LAN ne
ed to support the VLAN (802.1Q)
standard.
• The authentication is set to any RADIUS
type authentication: either the
network authentication in the wireless security profile or the remote MAC
address database authentication for the MAC Authentication feature can be
used.
VLAN ID Enter the default VLAN ID that needs to be associated with this wireless security
profile
. The default VLAN ID is 1. The VLAN ID needs to match the VLAN ID that
is used by the other devices in your network.
Access Control
Note: Access control functions only when static
VLANs are enabled, that is, you
select Disable from the Dynamic VLAN drop-down list.
The Access Control radio buttons let you enable or disable access control
th
rough a RADIUS server to ensure that clients are connected to the wireless
access point through the correct VLAN.
• Dis
able. Access control is disabled. This is the default setting.
• En
able. Access control is enabled. Clients are authenticated through a
RADIUS server.
Access Control Policy When access control is enabled, the access
control policy lets you specify
whether or not a client can access the wireless access point when the client is
not authenticated because the VLAN ID is incorrect.
Select a radio button to enable or disable access:
• Disab
le. If the RADIUS server does not authenticate the client, the client is
still allowed to connect to the wireless access point through the default VLAN
(which is specified in the VLAN ID field) instead of through the VLAN to which
the client is assigned in the RADIUS server.
• Enable. If th
e RADIUS server does not authenticate the client, the client is not
allowed to connect to the wireless access point.
Table 10. Authentication Settings of the Edit Security Profile Screen (Continued)
Field Description
- ProSafe Dual Band 1
- Wireless-N Access Point 1
- WNDAP360 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Contents 3
- Chapter 4 Management 4
- Chapter 6 Troubleshooting 4
- Introduction 6
- What Is In the Box? 7
- System Requirements 7
- Key Features and Standards 8
- Key Features 9
- Networking 10
- Hardware Description 11
- Rear Panel 12
- Figure 3 13
- Ethernet Cabling Requirements 15
- Figure 4 16
- Web Management Interface 18
- Figure 8 19
- To configure time settings: 20
- 3. Click Apply 20
- to save your settings 20
- To configure the IP settings: 21
- 1. Select Con 21
- Figure 11 22
- Figure 12 24
- Figure 13 27
- Ceiling Installation 31
- 5. Connect th 32
- Wall Installation 33
- 4. Connect th 34
- Desk Installation 35
- Figure 14 37
- Security Profiles 38
- Figure 15 42
- Figure 16 42
- Figure 17 43
- Figure 18 47
- Figure 19 47
- Configure Legacy 802.1X 48
- Figure 21 49
- Figure 22 49
- Figure 23 49
- Figure 24 50
- Figure 25 50
- Figure 26 50
- Figure 27 52
- Figure 28 54
- Figure 29 55
- Field Description 56
- Figure 30 57
- Management 58
- SNMP Management 59
- Figure 32 60
- Figure 33 61
- Web Browser Upgrade Procedure 62
- TFTP Server Upgrade Procedure 63
- Defaults 64
- Restore the Configuration 65
- Settings 66
- Default Configuration 67
- Figure 40 68
- Enable the Syslog Server 69
- View System Information 70
- Monitor Wireless Stations 72
- Figure 43 73
- Figure 44 73
- View the Activity Log 75
- Traffic Statistics 75
- Statistics screen: 76
- Figure 47 78
- Figure 48 79
- To configure STP and VLANs: 82
- Figure 49 82
- Hotspot Settings 83
- Figure 51 84
- To configure advanced QoS: 87
- Figure 52 87
- Table 25. EDCA Settings 88
- Configure Wireless Bridging 89
- Wireless PC card 90
- Figure 54 91
- Figure 55 91
- Figure 58 95
- Figure 59 98
- Figure 60 99
- Figure 61 100
- Advanced Configuration 101
- Troubleshooting 103
- Basic Functioning 104
- Wireless-Capable Computer 105
- Request timed out 107
- Problems with Date and Time 108
- Use the Packet Capture Tool 109
- Supplemental Information 110
- Factory Default Settings 112
- Command-Line Reference 115
- Notification of Compliance 128
- FCC Information to User 130
- FCC Declaration of Conformity 130
- FCC Caution 130
- Industry Canada 131
- Industrie Canada 131
- Numerics 132
Related products and manuals for WLAN access points Netgear WNDAP360
WLAN access points Netgear DG834G User Manual
(166 pages)
(166 pages)
WLAN access points Netgear WG102 User Manual
(134 pages)
(134 pages)
WLAN access points Netgear WNDAP330 User's Guide
(142 pages)
(142 pages)
© 2020, manymanuals.com. All rights reserved. | 0.570 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals