Netgear WNDAP360 User Manual Page 131
- Page / 137
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Notification of Compliance
131
ProSafe Dual Band Wireless-N Access Point WNDAP360
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
• For prod
ucts available in the USA market, only channel 1 ~ 11 can be operated. Selection of other channels is
not possible.
Industry Canada
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been designed to operate with an antenna having a maximum gain of 6.29dB. Antenna having a
high
er gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.
Under Industry Canada regulations, this ra
dio transmitter may only operate using an antenna of a type and maximum
(or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.
IMPORTANT NOTE: Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator and your body.
Caution
The device for operation in the band 5150 - 5250 MHz is only for indoor usage to reduce the potential for harmful
interference to co-channel mobile satellite systems.
High power radars are allocated as primary users (th
at is, priority users) of the bands 5250 - 5350 MHz and
5650 - 5850 MHz and these radars could cause interferen
ce and/or damage to LE-LAN devices.
Industrie Canada
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un
fonctionnement indésirable.
Ce dispositif a été conçu pour fonctionner avec une antenn
e ayant un gain maximal de dB 6.29. Une antenne à gain
plus élevé est strictement interdite par les règlements d'Industrie Canada. L'impédance d'antenne requise est de
50 ohms.
Conformément à la réglementation d'Indu
strie Canada, le présent émetteur radio peutfonctionner avec une antenne
d'un type et d'un gain maximal (ou inférieur) approuvé pourl'émetteur par Industrie Canada. Dans le but de réduire les
risques de brouillage radioélectriqueà l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de
sorte que lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire àl'établissement
d'une communication satisfaisante.
NOTE IMPORTANTE: Déclaration d'exposition aux radiations
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de
rayonnement et votre corps.
Avertissement
Les dispositifs fonctionnant dans la bande 5150 - 5250 MHz sont réservés uniquement pour une utilisation à
l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux.
De plus, les utilisateurs devraient aussi être
avisés que les utilisateurs de radars de haute puissance sont désignés
utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250 - 5350 MHz et 5650 - 5850 MHz et que
ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
- ProSafe Dual Band 1
- Wireless-N Access Point 1
- WNDAP360 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Contents 3
- Chapter 4 Management 4
- Chapter 6 Troubleshooting 4
- Introduction 6
- What Is In the Box? 7
- System Requirements 7
- Key Features and Standards 8
- Key Features 9
- Networking 10
- Hardware Description 11
- Rear Panel 12
- Figure 3 13
- Ethernet Cabling Requirements 15
- Figure 4 16
- Web Management Interface 18
- Figure 8 19
- To configure time settings: 20
- 3. Click Apply 20
- to save your settings 20
- To configure the IP settings: 21
- 1. Select Con 21
- Figure 11 22
- Figure 12 24
- Figure 13 27
- Ceiling Installation 31
- 5. Connect th 32
- Wall Installation 33
- 4. Connect th 34
- Desk Installation 35
- Figure 14 37
- Security Profiles 38
- Figure 15 42
- Figure 16 42
- Figure 17 43
- Figure 18 47
- Figure 19 47
- Configure Legacy 802.1X 48
- Figure 21 49
- Figure 22 49
- Figure 23 49
- Figure 24 50
- Figure 25 50
- Figure 26 50
- Figure 27 52
- Figure 28 54
- Figure 29 55
- Field Description 56
- Figure 30 57
- Management 58
- SNMP Management 59
- Figure 32 60
- Figure 33 61
- Web Browser Upgrade Procedure 62
- TFTP Server Upgrade Procedure 63
- Defaults 64
- Restore the Configuration 65
- Settings 66
- Default Configuration 67
- Figure 40 68
- Enable the Syslog Server 69
- View System Information 70
- Monitor Wireless Stations 72
- Figure 43 73
- Figure 44 73
- View the Activity Log 75
- Traffic Statistics 75
- Statistics screen: 76
- Figure 47 78
- Figure 48 79
- To configure STP and VLANs: 82
- Figure 49 82
- Hotspot Settings 83
- Figure 51 84
- To configure advanced QoS: 87
- Figure 52 87
- Table 25. EDCA Settings 88
- Configure Wireless Bridging 89
- Wireless PC card 90
- Figure 54 91
- Figure 55 91
- Figure 58 95
- Figure 59 98
- Figure 60 99
- Figure 61 100
- Advanced Configuration 101
- Troubleshooting 103
- Basic Functioning 104
- Wireless-Capable Computer 105
- Request timed out 107
- Problems with Date and Time 108
- Use the Packet Capture Tool 109
- Supplemental Information 110
- Factory Default Settings 112
- Command-Line Reference 115
- Notification of Compliance 128
- FCC Information to User 130
- FCC Declaration of Conformity 130
- FCC Caution 130
- Industry Canada 131
- Industrie Canada 131
- Numerics 132
Related products and manuals for WLAN access points Netgear WNDAP360
WLAN access points Netgear DG834G User Manual
(166 pages)
(166 pages)
WLAN access points Netgear WG102 User Manual
(134 pages)
(134 pages)
WLAN access points Netgear WNDAP330 User's Guide
(142 pages)
(142 pages)
© 2020, manymanuals.com. All rights reserved. | 0.632 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals