Netgear GSM7228PS User Manual Page 302
- Page / 799
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Routing Commands
302
ProSafe Managed Switch
passive-interface default (OSPF)
Use this command to enable global passive mode by default for all interfaces. It overrides
any interface level passive mode. OSPF will not form adjacencies over a passive interface.
Default
Format passive-interface default
Mode
no passive-interface default
Use this command to disable the global passive mode by default for all interfaces. Any
interface previously configured to be passive reverts to non-passive mode.
Format no passive-interface default
Mode
passive-interface (OSPF)
Use this command to set the interface or tunnel as passive. It overrides the global passive
mode that is currently effective on the interface or tunnel.
Default
Format passive-interface {<unit/slot/port>}
Mode
no passive-interface
Use this command to set the interface or tunnel as non-passive. It overrides the global
passive mode that is currently effective on the interface or tunnel.
Format no passive-interface {<unit/slot/port>}
Mode
timers pacing flood
To adjust the rate at which OSPFv2 sends LS Update packets, use this command in router
OSPFv2 global configuration mode. OSPF distributes routing information in Link State
Advertisements (LSAs), which are bundled into Link State Update (LS Update) packets. To
reduce the likelihood of sending a neighbor more packets than it can buffer, OSPF rate limits
the transmission of LS Update packets. By default, OSPF sends up to 30 updates per second
on each interface (1/the pacing interval). Use this command to adjust this packet rate.
disabled
Router OSPF Config
Router OSPF Config
disabled
Router OSPF Config
Router OSPF Config
Default
33 milliseconds
- ProSafe Managed Switch 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Contents 3
- Chapter 5 Routing Commands 4
- Chapter 13 Log Messages 6
- Chapter 15 Command List 7
- Licensing and Command Support 8
- Command Syntax 10
- Command Conventions 11
- Common Parameter Values 11
- Table 3. Type of Slots 12
- Using a Command’s “No” Form 13
- Managed Switch Modules 13
- Command Modes 14
- CLI Error Messages 18
- CLI Line-Editing Conventions 18
- Using CLI Help 19
- Accessing the CLI 20
- Stacking Commands 21
- For Each Interface: 30
- Non-Stop Forwarding Commands 31
- Port Configuration Commands 39
- Loopback Interface Commands 45
- VLAN Commands 64
- Double VLAN Commands 77
- Voice VLAN Commands 80
- Protected Ports Commands 82
- Private Group Commands 85
- Private VLAN 86
- GARP Commands 90
- GVRP Commands 92
- GMRP Commands 94
- Switching Commands 100
- ProSafe Managed Switch 101
- 802.1X Supplicant Commands 109
- Storm-Control Commands 112
- Flow Control Commands 122
- Port Mirroring 139
- Static MAC Filtering 141
- DHCP L2 Relay Agent Commands 145
- DHCP Client Commands 149
- MLD Snooping Commands 180
- vlanid 0-3600 184
- Port Security Commands 190
- LLDP (802.1AB) Commands 194
- LLDP-MED Commands 203
- Denial of Service Commands 212
- TCP Header Offset = 1 213
- MAC Database Commands 222
- ISDP Commands 224
- <unit/slot/port>] 231
- About MVR 232
- MVR Commands 232
- Example: 237
- Routing Commands 240
- IP Routing Commands 246
- Virtual LAN Routing Commands 266
- Commands 267
- DHCP and BOOTP Relay Commands 276
- IP Helper Commands 278
- 1583compatibility 283
- Table 1. Trapflags Groups 304
- Dampening 327
- ICMP Throttling Commands 336
- IP Multicast Commands 339
- DVMRP Commands 344
- PIM Commands 349
- Example 1: 357
- Example 2: 357
- (RP) advertisement 358
- Example 3: 359
- Example 4: 359
- IGMP Proxy Commands 367
- IPv6 Commands 373
- IPv6 Routing Commands 375
- 3ffe:1::1234/64 377
- C - connected, S - static 389
- ::0) and unsupported 394
- OSPFv3 Commands 398
- DHCPv6 Commands 431
- <pool-name> 437
- [<ipv6-address>] 437
- IPv6 Multicast Commands 439
- IPv6 PIM Commands 442
- IPv6 MLD Commands 449
- IPv6 MLD-Proxy Commands 455
- [<unit/slot/port>] 466
- DiffServ Class Commands 470
- DiffServ Policy Commands 479
- DiffServ Service Commands 484
- DiffServ Show Commands 485
- [in 489
- {deny 492
- {deny 498
- {deny 503
- AutoVOIP 508
- About PoE 518
- PoE Commands 519
- PSE-capable ports 527
- Utility Commands 529
- Auto Install Commands 530
- Dual Image Commands 532
- Logging Commands 550
- For example: 577
- For each configured server: 578
- DHCP Server Commands 579
- Message Received: 590
- Message Sent: 590
- DNS Client Commands 591
- Packet Capture Commands 595
- Cable Test Command 617
- [<index>] 621
- Software License Commands 622
- IP Address Conflict Commands 623
- RFC 2819 626
- RFC 3273 626
- RFC 3434 626
- UDLD Commands 631
- Management Commands 635
- Network Interface Commands 638
- Console Port Access Commands 641
- Telnet Commands 643
- Secure Shell (SSH) Commands 648
- Management Security Commands 651
- Access Commands 659
- User Account Commands 659
- SNMP Commands 683
- RADIUS Commands 694
- TACACS+ Commands 706
- <ip-address 707
- <priority> 710
- IPv6 Management Commands 716
- Log Messages 721
- Table 3. BSP Log Messages 722
- Table 4. NIM Log Messages 722
- Utilities 724
- Management 726
- Table 16. WEB Log Messages 728
- Table 18. SSHD Log Messages 728
- Table 19. SSLT Log Messages 729
- Switching 730
- Table 28. FDB Log Message 734
- Table 31. MFDB Log Message 734
- Table 36. ACL Log Messages 736
- Table 37. CoS Log Message 736
- Routing/IPv6 Routing 737
- Table 43. VRRP Log Messages 739
- Table 44. ARP Log Message 739
- Multicast 740
- Stacking 742
- Technologies 743
- O/S Support 745
- Captive Portal Commands 747
- Command List 773
Related products and manuals for Networking Netgear GSM7228PS
Networking Netgear WG111 User Manual
(77 pages)
(77 pages)
Networking Netgear WNA1100 User Manual
(48 pages)
(48 pages)
Networking Netgear CM212 User Manual
(19 pages)
(19 pages)
Networking Netgear WN111v2 User's Guide
(56 pages)
(56 pages)
Networking Netgear WGE101 User Manual
(17 pages)
(17 pages)
Networking Netgear DG834Gv5 User Manual
(44 pages)
(44 pages)
Networking Netgear GA311 User Manual
(52 pages)
(52 pages)
Networking Netgear WNA1000 User's Guide
(58 pages)
(58 pages)
Networking Netgear WNDAP330 User Manual
(7 pages)
(7 pages)
Networking Netgear RH340 User Manual
(6 pages)
(6 pages)
Networking Netgear WMS5316 User Manual
(70 pages)
(70 pages)
Networking Netgear DG834 V3 User Manual
(168 pages)
(168 pages)
Networking Netgear GA302T User Manual
(62 pages)
(62 pages)
Networking Netgear WC7600 User Manual
(307 pages)
(307 pages)
Networking Netgear WG111T User Manual
(49 pages)
(49 pages)
Networking Netgear 597E User's Guide
(49 pages)
(49 pages)
© 2020, manymanuals.com. All rights reserved. | 4.072 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals