Netgear WAG302v2 User Manual Page 31
- Page / 104
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual
Basic Installation and Configuration 2-9
v1.0, May 2006
• Access Point Name. This unique name is the access point NetBIOS name. The default
Access Point Name is on the bottom label of the WAG302v2. The default name is
netgearxxxxxx, where xxxxxx represents the last six hexadecimal digits of the
WAG302v2 MAC address. You can change the name to a unique name up to 15 characters
long.
• Country/Region. This is the region where the WAG302v2 can be used. It may not be
legal to operate the wireless features of the wireless access point in a region other than one
of those identified in this field. For products sold in the United States, the default country
domain is preset. For products sold outside of the United States, you must select a country
or region.
• DHCP Client: By default, the Dynamic Host Configuration Protocol (DHCP) client is
disabled. If you have a DHCP server on your LAN and you enable DHCP, the wireless
access point get its IP address, subnet mask and default gateway settings automatically
from the DHCP server on your network when you connect the WAG302v2 to your LAN.
• IP Address. The default IP address is 192.168.0.230. To change it, enter an unused IP
address from the address range used on your LAN (factory default: 192.168.0.230); or
enable DHCP.
• IP Subnet Mask. Enter the subnet mask value used on your LAN (factory default:
255.255.255.0).
• Default Gateway. Enter the IP address of the gateway for your LAN. For more complex
networks, enter the address of the router for the network segment to which the wireless
access point is connected (factory default: 0.0.0.0).
• DNS Server. Enter the IP address of the Domain Name Server (DNS) you want to use
(factory default: 0.0.0.0).
• Spanning Tree Protocol. Enable or disable spanning tree protocol (factory default:
enabled). Spanning tree protocol provides network traffic optimization in settings with
multiple WAG302v2 Wireless Access Points.
Note: To connect to the WAG302v2 after the DHCP server on your network
assigns it a new IP address, enter the access point name into the address
field of your Web browser. The default access point name is
netgearxxxxxx, where xxxxxx represents the last 6 bytes of the MAC
address. The default name is printed on the bottom label of the
WAG302v2.
- NETGEAR ProSafe Dual 1
- Band Wireless Access 1
- Point WAG302v2 1
- Reference Manual 1
- FOR HOME OR OFFICE USE 2
- FCC Statement 3
- Contents 9
- About This Manual 13
- How to Use This Manual 14
- How to Print this Manual 15
- Chapter 1 17
- Introduction 17
- WAG302v2 Key Features 18
- Introduction 1-3 19
- What’s In the Box? 20
- Hardware Description 21
- Rear Panel 22
- Chapter 2 23
- Figure 2-1 26
- Figure 2-2 27
- Figure 2-3 29
- Figure 2-4 29
- Basic IP Settings 30
- Wireless Settings 32
- Figure 2-6 33
- Configuring Security Profiles 35
- Figure 2-7 37
- Profile Definition 38
- Network Authentication 38
- Data Encryption 39
- Figure 2-8 42
- Figure 2-9 44
- Chapter 3 47
- Management and Information 47
- Remote Management 48
- Figure 3-3 49
- CLI Commands 50
- Configuration File Management 51
- Erasing the Configuration 52
- Viewing General Information 53
- Viewing the Activity Log 55
- Figure 3-7 56
- Viewing Statistics 57
- Rogue AP Detection 58
- Figure 3-9 59
- Chapter 4 61
- Advanced Configuration 61
- 4-2 Advanced Configuration 62
- Configuring Hotspot Settings 63
- 4-4 Advanced Configuration 64
- Figure 4-3 64
- Advanced Configuration 4-5 65
- 4-6 Advanced Configuration 66
- Advanced Configuration 4-7 67
- 4-8 Advanced Configuration 68
- Figure 4-4 68
- Advanced Configuration 4-9 69
- Figure 4-5 69
- 4-10 Advanced Configuration 70
- Figure 4-6 70
- Advanced Configuration 4-11 71
- 4-12 Advanced Configuration 72
- Figure 4-7 72
- Advanced Configuration 4-13 73
- 4-14 Advanced Configuration 74
- Chapter 5 75
- Troubleshooting 75
- The LAN light is not lit 76
- Troubleshooting 5-3 77
- 5-4 Troubleshooting 78
- Appendix A 79
- Related Documents 79
- A-2 Related Documents 80
- Appendix B 81
- Specifications 81
- B-2 Specifications 82
- Specifications B-3 83
- B-4 Specifications 84
- Appendix C 85
- Command Line Reference 85
- Keyboard Shortcuts 86
- Interface Naming Conventions 87
- Entering CLI Commands 88
- Command Line Reference C-5 89
- Configuring Basic Settings 91
- Configuring Wireless Settings 92
- C-10 Command Line Reference 94
- Command Line Reference C-11 95
- RADIUS Server Settings 96
- Access Control 97
- C-14 Command Line Reference 98
- Table C-12 AP Management 98
- Command Line Reference C-15 99
- Table C-13 AP Information 99
- C-16 Command Line Reference 100
- Hotspot Settings 101
- Advanced Wireless Settings 101
- C-20 Command Line Reference 104
Related products and manuals for WLAN access points Netgear WAG302v2
WLAN access points Netgear WG602 User Manual
(15 pages)
(15 pages)
WLAN access points Netgear WNAP210 User Manual
(126 pages)
(126 pages)
WLAN access points Netgear WG102 User Manual
(70 pages)
(70 pages)
WLAN access points Netgear WNDAP350 User Manual
(136 pages)
(136 pages)
WLAN access points Netgear ME101 User Manual
(23 pages)
(23 pages)
WLAN access points Netgear WNAP320 User's Guide
(126 pages)
(126 pages)
© 2020, manymanuals.com. All rights reserved. | 0.784 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals