Netgear WAG302v2 User Manual Page 88
- Page / 104
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual
C-4 Command Line Reference
v1.0, May 2006
Entering CLI Commands
This section describes how to use CLI commands to configure the access point and how to view
system settings and information.
Table C-3 shows the commands available at the blank CLI prompt. You can type TAB twice to
display the list of commands. After you enter the command, press the TAB key twice to display a
list of available keywords and variables.
lo Local loopback for data meant for the access point itself.
eth0 The Ethernet interface connected to the Internal network.
vlan1 The VLAN interface associated with the default security profile.
wlan0 The default security profile for the Internal network on radio 1.
wlan1 The default security profile for the Internal network on radio 2.
wlan0vapx The wireless interface for the x security profile on radio 1.
wlan1vapx The wireless interface for the x security profile on radio 2.
wlan0wdsx A wireless distribution system (WDS) interface on radio 1 where x indicates the number of
the WDS link. The WDS interface allows you to configure wireless bridging and repeating.
wlan1wdsx A wireless distribution system (WDS) interface on radio 2 where x indicates the number of
the WDS link. The WDS interface allows you to configure wireless bridging and repeating.
Note: The commands and examples in this appendix use radio 1. To configure and view
information about the second radio, replace the “wlan0” portion of the interface
name with wlan1. Use the command get radio all to view information about
the radios on the WAG302v2.
Table C-3 Commands at the Blank Prompt
Command Description
get
Gets the property values of existing instances of a class.
set Sets the property values of existing instances of a class.
add
Adds a new instance or group of instances of a class.
remove
Removes an existing instance of a class.
Table C-2 Interface Naming Convention (continued)
Interface Description
- NETGEAR ProSafe Dual 1
- Band Wireless Access 1
- Point WAG302v2 1
- Reference Manual 1
- FOR HOME OR OFFICE USE 2
- FCC Statement 3
- Contents 9
- About This Manual 13
- How to Use This Manual 14
- How to Print this Manual 15
- Chapter 1 17
- Introduction 17
- WAG302v2 Key Features 18
- Introduction 1-3 19
- What’s In the Box? 20
- Hardware Description 21
- Rear Panel 22
- Chapter 2 23
- Figure 2-1 26
- Figure 2-2 27
- Figure 2-3 29
- Figure 2-4 29
- Basic IP Settings 30
- Wireless Settings 32
- Figure 2-6 33
- Configuring Security Profiles 35
- Figure 2-7 37
- Profile Definition 38
- Network Authentication 38
- Data Encryption 39
- Figure 2-8 42
- Figure 2-9 44
- Chapter 3 47
- Management and Information 47
- Remote Management 48
- Figure 3-3 49
- CLI Commands 50
- Configuration File Management 51
- Erasing the Configuration 52
- Viewing General Information 53
- Viewing the Activity Log 55
- Figure 3-7 56
- Viewing Statistics 57
- Rogue AP Detection 58
- Figure 3-9 59
- Chapter 4 61
- Advanced Configuration 61
- 4-2 Advanced Configuration 62
- Configuring Hotspot Settings 63
- 4-4 Advanced Configuration 64
- Figure 4-3 64
- Advanced Configuration 4-5 65
- 4-6 Advanced Configuration 66
- Advanced Configuration 4-7 67
- 4-8 Advanced Configuration 68
- Figure 4-4 68
- Advanced Configuration 4-9 69
- Figure 4-5 69
- 4-10 Advanced Configuration 70
- Figure 4-6 70
- Advanced Configuration 4-11 71
- 4-12 Advanced Configuration 72
- Figure 4-7 72
- Advanced Configuration 4-13 73
- 4-14 Advanced Configuration 74
- Chapter 5 75
- Troubleshooting 75
- The LAN light is not lit 76
- Troubleshooting 5-3 77
- 5-4 Troubleshooting 78
- Appendix A 79
- Related Documents 79
- A-2 Related Documents 80
- Appendix B 81
- Specifications 81
- B-2 Specifications 82
- Specifications B-3 83
- B-4 Specifications 84
- Appendix C 85
- Command Line Reference 85
- Keyboard Shortcuts 86
- Interface Naming Conventions 87
- Entering CLI Commands 88
- Command Line Reference C-5 89
- Configuring Basic Settings 91
- Configuring Wireless Settings 92
- C-10 Command Line Reference 94
- Command Line Reference C-11 95
- RADIUS Server Settings 96
- Access Control 97
- C-14 Command Line Reference 98
- Table C-12 AP Management 98
- Command Line Reference C-15 99
- Table C-13 AP Information 99
- C-16 Command Line Reference 100
- Hotspot Settings 101
- Advanced Wireless Settings 101
- C-20 Command Line Reference 104
Related products and manuals for WLAN access points Netgear WAG302v2
WLAN access points Netgear WG602 User Manual
(15 pages)
(15 pages)
WLAN access points Netgear WNAP210 User Manual
(126 pages)
(126 pages)
WLAN access points Netgear WG102 User Manual
(70 pages)
(70 pages)
WLAN access points Netgear WNDAP350 User Manual
(136 pages)
(136 pages)
WLAN access points Netgear ME101 User Manual
(23 pages)
(23 pages)
WLAN access points Netgear WNAP320 User's Guide
(126 pages)
(126 pages)
© 2020, manymanuals.com. All rights reserved. | 3.609 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals