Netgear WAG302v2 User Manual Page 71
- Page / 104
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
NETGEAR ProSafe Dual Band Wireless Access Point WAG302v2 Reference Manual
Advanced Configuration 4-11
v1.0, May 2006
• Configure WAG302v2 (AP 2) on LAN Segment 2 in Point-to-Point Bridge mode with the
Remote MAC Address of AP 1.
• Configure the WAG302v2 (AP 3) on LAN 3 in Point-to-Point Bridge mode with the
Remote MAC Address of AP 1.
2. Verify the following for all access points:
• The LAN network configuration of the WAG302v2 Wireless Access Points are configured
to operate in the same LAN network address range as the LAN devices
• Only one AP is configured in Point-to-Multi-Point Bridge mode, and all the others are in
Point-to-Point Bridge mode.
• All APs must be on the same LAN. That is, all the AP LAN IP addresses must be in the
same network.
• If using DHCP, all WAG302v2 Wireless Access Points should be set to “Obtain an IP
address automatically (DHCP Client)” in the IP Address Source portion of the Basic IP
Settings menu.
• All WAG302v2 Wireless Access Points must use the same SSID, Channel, authentication
mode, if any, and encryption in use.
• All Point-to-Point APs must have the MAC address of AP 1 in the Remote AP MAC
address field.
3. Verify connectivity across the LANs.
• A computer on any LAN segment should be able to connect to the Internet or share files
and printers with any other PCs or servers connected to any of the three LAN segments.
• Wireless stations will not be able to connect to the WAG302v2 Wireless Access Points in
Figure 4-6. If you require wireless stations to access any LAN segment, you can use
additional WAG302v2 Wireless Access Points configured in Wireless Access Point mode
to any LAN segment.
Note: You can extend this multi-point bridging by adding additional WAG302v2s
configured in Point-to-Point mode for each additional LAN segment. Furthermore,
you can extend the range of the wireless network with NETGEAR wireless antenna
accessories.
- NETGEAR ProSafe Dual 1
- Band Wireless Access 1
- Point WAG302v2 1
- Reference Manual 1
- FOR HOME OR OFFICE USE 2
- FCC Statement 3
- Contents 9
- About This Manual 13
- How to Use This Manual 14
- How to Print this Manual 15
- Chapter 1 17
- Introduction 17
- WAG302v2 Key Features 18
- Introduction 1-3 19
- What’s In the Box? 20
- Hardware Description 21
- Rear Panel 22
- Chapter 2 23
- Figure 2-1 26
- Figure 2-2 27
- Figure 2-3 29
- Figure 2-4 29
- Basic IP Settings 30
- Wireless Settings 32
- Figure 2-6 33
- Configuring Security Profiles 35
- Figure 2-7 37
- Profile Definition 38
- Network Authentication 38
- Data Encryption 39
- Figure 2-8 42
- Figure 2-9 44
- Chapter 3 47
- Management and Information 47
- Remote Management 48
- Figure 3-3 49
- CLI Commands 50
- Configuration File Management 51
- Erasing the Configuration 52
- Viewing General Information 53
- Viewing the Activity Log 55
- Figure 3-7 56
- Viewing Statistics 57
- Rogue AP Detection 58
- Figure 3-9 59
- Chapter 4 61
- Advanced Configuration 61
- 4-2 Advanced Configuration 62
- Configuring Hotspot Settings 63
- 4-4 Advanced Configuration 64
- Figure 4-3 64
- Advanced Configuration 4-5 65
- 4-6 Advanced Configuration 66
- Advanced Configuration 4-7 67
- 4-8 Advanced Configuration 68
- Figure 4-4 68
- Advanced Configuration 4-9 69
- Figure 4-5 69
- 4-10 Advanced Configuration 70
- Figure 4-6 70
- Advanced Configuration 4-11 71
- 4-12 Advanced Configuration 72
- Figure 4-7 72
- Advanced Configuration 4-13 73
- 4-14 Advanced Configuration 74
- Chapter 5 75
- Troubleshooting 75
- The LAN light is not lit 76
- Troubleshooting 5-3 77
- 5-4 Troubleshooting 78
- Appendix A 79
- Related Documents 79
- A-2 Related Documents 80
- Appendix B 81
- Specifications 81
- B-2 Specifications 82
- Specifications B-3 83
- B-4 Specifications 84
- Appendix C 85
- Command Line Reference 85
- Keyboard Shortcuts 86
- Interface Naming Conventions 87
- Entering CLI Commands 88
- Command Line Reference C-5 89
- Configuring Basic Settings 91
- Configuring Wireless Settings 92
- C-10 Command Line Reference 94
- Command Line Reference C-11 95
- RADIUS Server Settings 96
- Access Control 97
- C-14 Command Line Reference 98
- Table C-12 AP Management 98
- Command Line Reference C-15 99
- Table C-13 AP Information 99
- C-16 Command Line Reference 100
- Hotspot Settings 101
- Advanced Wireless Settings 101
- C-20 Command Line Reference 104
Related products and manuals for WLAN access points Netgear WAG302v2
WLAN access points Netgear WG602 User Manual
(15 pages)
(15 pages)
WLAN access points Netgear WNAP210 User Manual
(126 pages)
(126 pages)
WLAN access points Netgear WG102 User Manual
(70 pages)
(70 pages)
WLAN access points Netgear WNDAP350 User Manual
(136 pages)
(136 pages)
WLAN access points Netgear ME101 User Manual
(23 pages)
(23 pages)
WLAN access points Netgear WNAP320 User's Guide
(126 pages)
(126 pages)
© 2020, manymanuals.com. All rights reserved. | 0.879 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals