Netgear WNAP320 User's Guide Page 90
- Page / 126
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
90 | Chapter 5. Advanced Configuration
ProSafe Wireless-N Access Point WNAP320 Reference Manual
f. Specify the settings as explained in the following table:
g. Click Apply to
save your security profile settings. The Bridging screen displays
again.
h. Repeat step b through step g for any other security profile that you want to edit.
Table 26. Point-to-Multipoint Bridge Profile and Authentication Settings
Field Description
Profile Definition
Profile Name Enter a profile name that is easy to remember. The default names for the four
secu
rity profiles are NETGEAR-WDS-1, NETGEAR-WDS-2,
NETGEAR-WDS-3, and NETGEAR-WDS-4.
Remote MAC Address Enter the MAC address of the remote wireless access point (the MAC
ad
dress of AP2 or AP 3 on LAN Segment 1 in Figure 54 on
page 88).
Authentication Settings
Network Authentication
and
Data Encryption
From the Network Authentication drop-down list, select Open System,
WPA-PSK, or WPA2-PSK. Your selection determines the options that the
Data Encryption drop-down list provides, and whether or not the WPA
Passphrase (Network Key) field displays.
Open System Although you can use the bridge co
mmunication without any
authentication and encryption, NETGEAR recommends that
you use WEP if you do select an open system. From the
Data Encryption drop-down list, select one of the following:
• None. No
authentication and encryption.
• 64-b
it WEP. Standard WEP encryption, using 40/64-bit
encryption.
• 12
8-bit WEP. Standard WEP encryption, using 104/128-bit
encryption.
• 152
-bit WEP. Proprietary WEP encryption mode, using
128+24 bits encryption. This mode functions only with
other wireless station that support this mode.
WPA-PSK TKIP (T
emporal Key Integrity Protocol) is the standard
encryption method used with WPA-PSK and the only
selection possible from the Data Encryption drop-down list.
In the WPA Passphrase (Network Key) field, enter a
p
assphrase. The passphrase length must be between 8 and
63 characters (inclusive).
WPA2-PSK AES (Adva
nced Encryption Standard) is the standard
encryption method used with WPA2-PSK and the only
selection possible from the Data Encryption drop-down list.
In the WPA Passphrase (Network Key) field, enter a
p
assphrase. The passphrase length must be between 8 and
63 characters (inclusive).
Note: NETGEAR recommends WPA2-PSK authentication
with AES en
cryption if you want to use the 11n rates and
speed.
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Contents 3
- Chapter 4 Management 4
- Chapter 6 Troubleshooting 4
- Contents 5
- Introduction 6
- What Is In the Box? 7
- System Requirements 7
- Key Features and Standards 7
- Key Features 8
- Hardware Description 10
- Top Panel 11
- Rear Panel 12
- Figure 3 13
- Ethernet Cabling Requirements 15
- Figure 4 17
- Web Management Interface 18
- Figure 7 19
- Figure 8 19
- Figure 9 20
- To configure the IP settings: 21
- 1. Select Con 21
- Figure 11 22
- Table 5. LAN Settings 23
- Figure 12 24
- Ceiling Installation 28
- 5. Conn 29
- Wall Installation 30
- 4. Conn 31
- Desk Installation 33
- Figure 13 35
- Security Profiles 36
- Figure 14 39
- Figure 15 40
- Figure 16 44
- Figure 17 44
- Configure Legacy 802.1X 45
- Figure 20 46
- Figure 21 46
- • WPA-PSK 47
- • WPA2-PSK 47
- • WPA-PSK & WPA2-PSK 47
- Figure 25 48
- 3. Click App 49
- Figure 26 50
- Schedule the Wireless Radio 52
- Figure 28 53
- Management 55
- SNMP Management 56
- Figure 30 57
- Figure 31 57
- Web Browser Upgrade Procedure 59
- TFTP Server Upgrade Procedure 59
- Defaults 60
- Restore the Configuration 61
- Settings 62
- Default Configuration 63
- Figure 37 64
- Figure 38 64
- Enable the Syslog Server 65
- View System Information 66
- Monitor Wireless Stations 68
- Figure 42 69
- View the Activity Log 70
- Traffic Statistics 71
- Figure 45 73
- Figure 46 74
- Field Description 75
- Advanced Configuration 76
- Figure 47 77
- Hotspot Settings 78
- Figure 49 79
- Figure 50 82
- Table 24. EDCA Settings 83
- Configure Wireless Bridging 84
- Figure 51 85
- Figure 52 86
- Figure 53 86
- Figure 54 88
- Figure 55 89
- Figure 56 89
- Figure 57 92
- Figure 58 93
- Figure 59 93
- Figure 60 96
- Troubleshooting 97
- Basic Functioning 98
- Wireless-Capable Computer 99
- Problems with Date and Time 103
- Use the Packet Capture Tool 103
- Supplemental Information 105
- Technical Specifications 106
- Factory Default Settings 107
- Command-Line Reference 109
- Notification of Compliance 117
- FCC Caution 118
- Industry Canada statement: 118
- Radiation Exposure Statement: 118
- Interference Reduction Table 120
- Numerics 121
- 122 122
- Index 123
- 124 124
- Index 125
- 126 126
Related products and manuals for WLAN access points Netgear WNAP320
WLAN access points Netgear WNDAP620 User Manual
(172 pages)
(172 pages)
WLAN access points Netgear WN604 User Manual
(70 pages)
(70 pages)
WLAN access points Netgear WAG102 User Manual
(102 pages)
(102 pages)
WLAN access points Netgear WGR614 v4 User Manual
(152 pages)
(152 pages)
WLAN access points Netgear MA101 User Manual
(67 pages)
(67 pages)
WLAN access points Netgear 802.11g User Manual
(108 pages)
(108 pages)
WLAN access points Netgear WG602v2 User's Guide
(122 pages)
(122 pages)
© 2020, manymanuals.com. All rights reserved. | 0.686 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals