Netgear GS728TPP User Manual Page 20
- Page / 277
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
20
GS752TP, GS728TP, and GS728TPP Gigabit Smart Switches
The Device View is available by selecting System Device View.
Depending upon the status of the port, the LED of the port status lights. Green indicates that
the port is enabled. Red indicates that an error occurred on the port and the link is disabled.
The LED of the port speed light in either green or yellow.
• A green LED indicates operational ports at the link speed of 1000 Mbps.
• A yellow LED indicates operational ports at the link speed of 10/100 Mbps.
The system LEDs are on the left side of the front panel.
Power/Status LED
The Power LED is a bicolor LED that serves as an indicator of power and diagnostic status.
The following indications are given by the following LED states:
• A solid green LED indicates that the power is supplied to the switch from the internal
power supply and is operating normally.
• A blinking green LED indicates that the internal power supply has failed, and that the
system is drawing power from a remote power supply or PoE power from an external
power supply.
• A solid yellow LED indicates that system is in the boot-up stage.
• No lit LED indicates that power is disconnected.
FAN Status LED
FAN status is indicated as follows:
• A solid yellow LED indicates that the fan is faulty.
• No lit LED indicates that the fan is operating normally.
Max PoE LED
The Max PoE LED indicates the following:
• A solid yellow LED indicates that less than seven watts of PoE power are available.
• A blinking yellow LED indicates that the PoE Max LED was lit within the previous 2
minutes.
• No lit LED indicates that at least seven watts of PoE power are available.
LED Status LED
The LED Status LED indicates the following:
• A solid green LED indicates that the Port LED is in Ethernet Mode.
• A solid yellow LED indicates that the Port LED is in PoE Mode.
- GS752TP, GS728TP, and 1
- GS728TPP Gigabit Smart 1
- Switches 1
- Trademarks 2
- Revision History 2
- Contents 3
- Chapter 8 Maintenance 6
- Chapter 9 Help 6
- Getting Started 8
- Switch Management Interface 10
- Understand the User Interface 17
- Device View 19
- Device View 20
- Figure 3. Device View 21
- Use SNMP 22
- SNMP SNMPv1/v2 23
- Interface Naming Convention 24
- Management 26
- IP Configuration 27
- IPv6 Network Configuration 29
- IPv6 Network Neighbors 31
- Time Configuration 32
- field is disabled 33
- Time (UTC) time zone in 33
- SNTP Server Configuration 34
- To remove an SNTP server: 35
- DNS Configuration 36
- Host Configuration 37
- Green Ethernet Configuration 38
- Green Ethernet Detail 41
- Green Ethernet Summary 42
- PoE Configuration 44
- PoE Port Configuration 45
- Timer Global Configuration 46
- Timer Schedule 47
- SNMP V1/V2 49
- Trap Configuration 51
- Trap Flags 52
- SNMP Supported MIBs 53
- SNMP v3 User Configuration 53
- LLDP Configuration 56
- LLDP Port Settings 57
- LLDP-MED Network Policy 58
- LLDP-MED Port Settings 59
- Local Information 60
- Port Information table 61
- Ports on page 73 61
- Neighbors Information 63
- Table 10. Port Details 64
- Services—DHCP Snooping 67
- Global Configuration 73
- Port Configuration 74
- Link Aggregation Groups 76
- To configure LAG settings: 77
- LAG Membership 78
- LACP Configuration 79
- LACP Port Configuration 80
- VLAN Configuration 81
- To configure VLANs: 82
- VLAN Membership Configuration 83
- Port VLAN ID Configuration 84
- Voice VLAN 86
- Voice VLAN Port Setting 88
- Voice VLAN OUI 88
- To configure OUI settings: 89
- Auto-VoIP Configuration 90
- Spanning Tree Protocol 91
- STP Configuration 92
- CST Configuration 94
- CST Port Configuration 96
- CST Port Status 97
- Rapid STP 98
- MST Configuration 99
- To modify an MST instance: 100
- MST instance 101
- MST Port Configuration 102
- Multicast 104
- Auto-Video Configuration 106
- IGMP Snooping 107
- IGMP Snooping Configuration 108
- IGMP Snooping Table 109
- IGMP Snooping Querier 111
- MLD Snooping 115
- To configure MLD snooping: 116
- MLD VLAN Configuration 117
- Static Multicast Address 119
- Multicast Group Membership 120
- Multicast Forward All 121
- Forwarding Database 122
- Dynamic Address Configuration 124
- Configuring Routing 125
- Configure IP Settings 126
- Configure VLAN Routing 127
- To configure VLAN settings: 128
- Configure and View Routes 130
- Configure ARP 132
- ARP Cache 133
- ARP Entry Configuration 134
- Global ARP Configuration 135
- ARP Entry Management 136
- Configure Quality of Service 137
- Class of Service 138
- CoS Interface Configuration 140
- Queue Configuration 141
- 802.1p to Queue Mapping 142
- DSCP to Queue Mapping 143
- Differentiated Services 144
- Diffserv Configuration 145
- DSCP Violate Action Mapping 145
- Class Configuration 147
- To configure a class: 148
- IPv6 Class Configuration 149
- To configure an IPv6 class: 150
- Policy Configuration 152
- Service Configuration 155
- Service Statistics 155
- Managing Device Security 157
- Management Security Settings 158
- Configure RADIUS Settings 159
- RADIUS Server Configuration 161
- Configure TACACS+ 163
- TACACS+ Server Configuration 164
- HTTP Authentication List 166
- HTTPS Authentication List 167
- Configure Management Access 169
- Secure HTTP Configuration 170
- Certificate Management 171
- Access Control 172
- Access Profile Configuration 173
- Access Rule Configuration 174
- Port Authentication 175
- Management 176
- Port Summary 180
- Traffic Control 182
- Security MAC Address 185
- Protected Ports 186
- ACL Wizard 187
- To create an ACL: 188
- MAC Rules 191
- To configure MAC ACL rules: 192
- MAC Binding Configuration 193
- √ appears in the box 194
- MAC Binding Table 195
- To configure an IP ACL: 196
- IP Rules 197
- IP Extended Rules 198
- IPv6 ACL 201
- IPv6 Rules 202
- IP Binding Configuration 204
- IP Binding Table 206
- Monitoring the System 207
- Switch Statistics 208
- Port Statistics 210
- Port Detailed Statistics 211
- EAP Statistics 215
- Cable Test 216
- Ports Cable Test 217
- Buffered Logs 218
- Logs Buffered Logs 219
- Server Log 220
- Trap Logs 222
- Mirroring 223
- System Resources Utilization 225
- Maintenance 226
- Device Reboot 227
- Factory Default 228
- Upload a File from the Switch 229
- Upload TFTP File Upload 230
- . Retrieve the syslog file 230
- HTTP File Upload 231
- Download a File to the Switch 232
- HTTP File Download 234
- File Management 235
- Dual Image Status 236
- Troubleshooting 238
- Ping IPv6 239
- Traceroute 240
- Remote Diagnostics 242
- 9. Help 243
- Online Help 244
- User Guide 245
- Registration 246
- To register the switch: 247
- MAC addresses 8 K 249
- Feature Value 249
- Switch Features and Defaults 250
- Configuration Examples 253
- Sample VLAN Configuration 255
- Access Control Lists (ACLs) 256
- DiffServ Traffic Classes 260
- Create Policies 260
- Sample DiffServ Configuration 261
- Sample 802.1x Configuration 264
- Sample MSTP Configuration 267
- VLAN Routing Overview 270
- Notification of Compliance 272
- FCC Declaration Of Conformity 273
- Numerics 274
Related products and manuals for Network switches Netgear GS728TPP
Network switches Netgear GS108E User Manual
(28 pages)
(28 pages)
(5 pages)© 2020, manymanuals.com. All rights reserved. | 0.761 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals