Netgear PROSAFE WG302v2 User Manual Page 28
- Page / 102
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual
2-6 Basic Installation and Configuration
v1.0, May 2006
c. Connect an Ethernet cable from your WG302v2 to a LAN port on your router, switch, or
hub.
d. Connect the power adapter to the wireless access point and plug the power adapter in to a
power outlet. The PWR, LAN, and WLAN lights should light up.
4. Verify wireless connectivity.
Using a computer with an 802.11b/g wireless adapter with the correct wireless settings needed
to connect to the WG302v2 (SSID, WEP/WPA, MAC ACL, etc.), verify connectivity by using
a browser such as Mozilla Firefox, Netscape, or Internet Explorer to browse the Internet, or
check for file and printer access on your network.
Note: By default, the DHCP client on the WG302v2 is disabled. If your network
uses dynamic IP addresses, you must change this setting. To connect to the
WG302v2 after the DHCP server on your network assigns it a new IP
address, enter the access point name into your Web browser. The default
access point name is netgearxxxxxx, where xxxxxx represents the last 6
bytes of the MAC address. The default name is printed on the bottom label
of the WG302v2.
Note: The default SSID is NETGEAR.The SSID of any wireless access adapters
must match the SSID you configure in the ProSafe 802.11g Wireless Access
Point. If they do not match, you will not get a wireless connection to the
WG302v2.
Note: If you are unable to connect to the WG302v2 with a wireless client, see
Chapter 5, “Troubleshooting
- NETGEAR ProSafe 1
- 802.11g Wireless Access 1
- Point WG302v2 1
- Reference Manual 1
- Radio Frequency Notice 2
- FCC Statement 3
- Channels: 1 to 13 7
- Contents 9
- About This Manual 13
- How to Use This Manual 14
- How to Print this Manual 14
- About This Manual xv 15
- Chapter 1 17
- Introduction 17
- WG302v2 Key Features 18
- Introduction 1-3 19
- What’s In the Box? 20
- Hardware Description 21
- Rear Panel 22
- Chapter 2 23
- Figure 2-1 26
- Figure 2-2 27
- Figure 2-3 29
- Figure 2-4 29
- Basic IP Settings 30
- Wireless Settings 32
- Configuring Security Profiles 35
- Figure 2-7 36
- Profile Definition 37
- Network Authentication 37
- Data Encryption 38
- Figure 2-8 42
- Figure 2-9 44
- Chapter 3 45
- Management and Information 45
- Remote Management 46
- Figure 3-3 47
- CLI Commands 48
- Configuration File Management 49
- Erasing the Configuration 50
- Viewing General Information 51
- Viewing the Activity Log 53
- Figure 3-7 54
- Viewing Statistics 55
- Rogue AP Detection 56
- Figure 3-9 57
- Chapter 4 59
- Advanced Configuration 59
- 4-2 Advanced Configuration 60
- Configuring Hotspot Settings 61
- 4-4 Advanced Configuration 62
- Figure 4-3 62
- Advanced Configuration 4-5 63
- 4-6 Advanced Configuration 64
- Advanced Configuration 4-7 65
- 4-8 Advanced Configuration 66
- Figure 4-4 66
- Advanced Configuration 4-9 67
- Figure 4-5 67
- 4-10 Advanced Configuration 68
- Figure 4-6 68
- Advanced Configuration 4-11 69
- 4-12 Advanced Configuration 70
- Figure 4-7 70
- Advanced Configuration 4-13 71
- 4-14 Advanced Configuration 72
- Chapter 5 73
- Troubleshooting 73
- The LAN light is not lit 74
- Troubleshooting 5-3 75
- 5-4 Troubleshooting 76
- Appendix A 77
- Related Documents 77
- A-2 Related Documents 78
- Appendix B 79
- Specifications 79
- B-2 Specifications 80
- Specifications B-3 81
- B-4 Specifications 82
- Appendix C 83
- Command Line Reference 83
- Keyboard Shortcuts 84
- Interface Naming Conventions 85
- Entering CLI Commands 86
- Command Line Reference C-5 87
- Configuring Basic Settings 89
- Configuring Wireless Settings 90
- C-10 Command Line Reference 92
- Command Line Reference C-11 93
- RADIUS Server Settings 94
- Access Control 95
- C-14 Command Line Reference 96
- Table C-12 AP Management 96
- Command Line Reference C-15 97
- Table C-13 AP Information 97
- C-16 Command Line Reference 98
- Advanced Wireless Settings 99
- Hotspot Settings 99
- Command Line Reference C-19 101
- C-20 Command Line Reference 102
Related products and manuals for WLAN access points Netgear PROSAFE WG302v2
WLAN access points Netgear DG834G User Manual
(166 pages)
(166 pages)
WLAN access points Netgear WG102 User Manual
(134 pages)
(134 pages)
WLAN access points Netgear WNDAP330 User's Guide
(142 pages)
(142 pages)
© 2020, manymanuals.com. All rights reserved. | 0.357 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals