Netgear PROSAFE WG302v2 User Manual Page 23
- Page / 102
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Basic Installation and Configuration 2-1
v1.0, May 2006
Chapter 2
Basic Installation and Configuration
This chapter describes how to set up your ProSafe 802.11g Wireless Access Point WG302v2 for
wireless connectivity to your LAN. This basic configuration enables computers with 802.11b/g
wireless adapters to do such things as connect to the Internet or access printers and files on your
LAN.
You need to prepare the following three things before you can establish a connection through your
wireless access point:
• A location for the WG302v2 that conforms to the Wireless Equipment Placement and Range
Guidelines described in this chapter.
• A wired connection from the WG302v2 to your LAN through a device such as a hub, switch,
router, or Cable/DSL gateway.
• One or more computers with properly configured 802.11b/g wireless adapters.
System Requirements
Before you install the WG302v2, make sure you have the following equipment and that your
system meets these requirements:
• A 10/100 Mbps Local Area Network device such as a hub or switch.
• The Category 5 UTP straight through Ethernet cable with RJ-45 connector included in the
package, or one like it.
• A 100-240 V, 50-60 HZ AC power source.
Note: Indoors, computers can connect over 802.11b/g wireless networks at ranges of
several hundred feet or more. This distance can allow others outside your area to
access your network. It is important to take appropriate steps to secure your
network from unauthorized access. The ProSafe 802.11g provides highly effective
security features which are covered in detail on the NETGEAR Web site. For more
information, see Appendix A, “Related Documents. Deploy the security features
appropriate to your needs.
- NETGEAR ProSafe 1
- 802.11g Wireless Access 1
- Point WG302v2 1
- Reference Manual 1
- Radio Frequency Notice 2
- FCC Statement 3
- Channels: 1 to 13 7
- Contents 9
- About This Manual 13
- How to Use This Manual 14
- How to Print this Manual 14
- About This Manual xv 15
- Chapter 1 17
- Introduction 17
- WG302v2 Key Features 18
- Introduction 1-3 19
- What’s In the Box? 20
- Hardware Description 21
- Rear Panel 22
- Chapter 2 23
- Figure 2-1 26
- Figure 2-2 27
- Figure 2-3 29
- Figure 2-4 29
- Basic IP Settings 30
- Wireless Settings 32
- Configuring Security Profiles 35
- Figure 2-7 36
- Profile Definition 37
- Network Authentication 37
- Data Encryption 38
- Figure 2-8 42
- Figure 2-9 44
- Chapter 3 45
- Management and Information 45
- Remote Management 46
- Figure 3-3 47
- CLI Commands 48
- Configuration File Management 49
- Erasing the Configuration 50
- Viewing General Information 51
- Viewing the Activity Log 53
- Figure 3-7 54
- Viewing Statistics 55
- Rogue AP Detection 56
- Figure 3-9 57
- Chapter 4 59
- Advanced Configuration 59
- 4-2 Advanced Configuration 60
- Configuring Hotspot Settings 61
- 4-4 Advanced Configuration 62
- Figure 4-3 62
- Advanced Configuration 4-5 63
- 4-6 Advanced Configuration 64
- Advanced Configuration 4-7 65
- 4-8 Advanced Configuration 66
- Figure 4-4 66
- Advanced Configuration 4-9 67
- Figure 4-5 67
- 4-10 Advanced Configuration 68
- Figure 4-6 68
- Advanced Configuration 4-11 69
- 4-12 Advanced Configuration 70
- Figure 4-7 70
- Advanced Configuration 4-13 71
- 4-14 Advanced Configuration 72
- Chapter 5 73
- Troubleshooting 73
- The LAN light is not lit 74
- Troubleshooting 5-3 75
- 5-4 Troubleshooting 76
- Appendix A 77
- Related Documents 77
- A-2 Related Documents 78
- Appendix B 79
- Specifications 79
- B-2 Specifications 80
- Specifications B-3 81
- B-4 Specifications 82
- Appendix C 83
- Command Line Reference 83
- Keyboard Shortcuts 84
- Interface Naming Conventions 85
- Entering CLI Commands 86
- Command Line Reference C-5 87
- Configuring Basic Settings 89
- Configuring Wireless Settings 90
- C-10 Command Line Reference 92
- Command Line Reference C-11 93
- RADIUS Server Settings 94
- Access Control 95
- C-14 Command Line Reference 96
- Table C-12 AP Management 96
- Command Line Reference C-15 97
- Table C-13 AP Information 97
- C-16 Command Line Reference 98
- Advanced Wireless Settings 99
- Hotspot Settings 99
- Command Line Reference C-19 101
- C-20 Command Line Reference 102
Related products and manuals for WLAN access points Netgear PROSAFE WG302v2
WLAN access points Netgear DG834G User Manual
(166 pages)
(166 pages)
WLAN access points Netgear WG102 User Manual
(134 pages)
(134 pages)
WLAN access points Netgear WNDAP330 User's Guide
(142 pages)
(142 pages)
© 2020, manymanuals.com. All rights reserved. | 1.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals