Netgear PROSAFE WG302v2 User Manual Page 60
- Page / 102
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual
4-2 Advanced Configuration
v1.0, May 2006
The following list provides information about how to configure DHCP settings:
• Use AP as DHCP Server: Turn on this option to allow the wireless access point to function as
a DHCP Server for wireless clients. The WG302v2 provides the pre-configured TCP/IP
configurations for wireless clients connected to this wireless access point. The default setting
is disable.
If you enable the WG302v2 DHCP server, you must configure the following TCP/IP configuration
information that the wireless access point assigns to wireless clients that associate with it:
• Starting IP Address: Enter the starting IP address the DHCP server on this Access Point can
assign wireless clients.The default starting IP address is 192.168.0.2.
• Ending IP Address: Enter the Ending IP address the DHCP server on this Access Point can
assign wireless clients. The default ending IP address is 192.168.0.50.
• Subnet Mask: Enter a subnet mask for the DHCP server on the Access Point to assign
wireless clients. The default subnet mask is 255.255.255.0.
• Gateway Address: Enter a Gateway Address for the DHCP server on the Access Point to
assign wireless clients. The wireless clients will use this IP address as the default gateway for
any traffic beyond the local network. By default, the gateway address is the IP address of the
WG302v2.
• Primary DNS Server: Enter a Primary DNS Server IP address for the DHCP server on the
Access Point to assign wireless clients. By default, the DNS server address is the IP address of
the WG302v2. The WG302v2 relays requests from wireless clients to the DNS server
configured on the Basic Settings page.
• Secondary DNS Server: Enter a Secondary DNS Server IP address for the DHCP server on
the Access Point to assign wireless clients. There is no default server.
• Primary WINS Server: Enter a Primary WINS Server IP address for the DHCP server on the
Access Point to assign wireless clients. There is no default server.
• Secondary WINS Server: Enter a Secondary WINS Server IP address for the DHCP server
on the Access Point to assign wireless clients. There is no default server.
Note: The DHCP server only assigns network information to clients that connect to
the WG302v2 through Security Profiles that are on the same VLAN as
Security Profile 1. VLAN 1 is the default VLAN for all Security Profiles. If
you typically use an existing DHCP server on your network to assign network
information to hosts, you do not need to enable the DHCP server on the
WG302v2.
- NETGEAR ProSafe 1
- 802.11g Wireless Access 1
- Point WG302v2 1
- Reference Manual 1
- Radio Frequency Notice 2
- FCC Statement 3
- Channels: 1 to 13 7
- Contents 9
- About This Manual 13
- How to Use This Manual 14
- How to Print this Manual 14
- About This Manual xv 15
- Chapter 1 17
- Introduction 17
- WG302v2 Key Features 18
- Introduction 1-3 19
- What’s In the Box? 20
- Hardware Description 21
- Rear Panel 22
- Chapter 2 23
- Figure 2-1 26
- Figure 2-2 27
- Figure 2-3 29
- Figure 2-4 29
- Basic IP Settings 30
- Wireless Settings 32
- Configuring Security Profiles 35
- Figure 2-7 36
- Profile Definition 37
- Network Authentication 37
- Data Encryption 38
- Figure 2-8 42
- Figure 2-9 44
- Chapter 3 45
- Management and Information 45
- Remote Management 46
- Figure 3-3 47
- CLI Commands 48
- Configuration File Management 49
- Erasing the Configuration 50
- Viewing General Information 51
- Viewing the Activity Log 53
- Figure 3-7 54
- Viewing Statistics 55
- Rogue AP Detection 56
- Figure 3-9 57
- Chapter 4 59
- Advanced Configuration 59
- 4-2 Advanced Configuration 60
- Configuring Hotspot Settings 61
- 4-4 Advanced Configuration 62
- Figure 4-3 62
- Advanced Configuration 4-5 63
- 4-6 Advanced Configuration 64
- Advanced Configuration 4-7 65
- 4-8 Advanced Configuration 66
- Figure 4-4 66
- Advanced Configuration 4-9 67
- Figure 4-5 67
- 4-10 Advanced Configuration 68
- Figure 4-6 68
- Advanced Configuration 4-11 69
- 4-12 Advanced Configuration 70
- Figure 4-7 70
- Advanced Configuration 4-13 71
- 4-14 Advanced Configuration 72
- Chapter 5 73
- Troubleshooting 73
- The LAN light is not lit 74
- Troubleshooting 5-3 75
- 5-4 Troubleshooting 76
- Appendix A 77
- Related Documents 77
- A-2 Related Documents 78
- Appendix B 79
- Specifications 79
- B-2 Specifications 80
- Specifications B-3 81
- B-4 Specifications 82
- Appendix C 83
- Command Line Reference 83
- Keyboard Shortcuts 84
- Interface Naming Conventions 85
- Entering CLI Commands 86
- Command Line Reference C-5 87
- Configuring Basic Settings 89
- Configuring Wireless Settings 90
- C-10 Command Line Reference 92
- Command Line Reference C-11 93
- RADIUS Server Settings 94
- Access Control 95
- C-14 Command Line Reference 96
- Table C-12 AP Management 96
- Command Line Reference C-15 97
- Table C-13 AP Information 97
- C-16 Command Line Reference 98
- Advanced Wireless Settings 99
- Hotspot Settings 99
- Command Line Reference C-19 101
- C-20 Command Line Reference 102
Related products and manuals for WLAN access points Netgear PROSAFE WG302v2
WLAN access points Netgear DG834G User Manual
(166 pages)
(166 pages)
WLAN access points Netgear WG102 User Manual
(134 pages)
(134 pages)
WLAN access points Netgear WNDAP330 User's Guide
(142 pages)
(142 pages)
© 2020, manymanuals.com. All rights reserved. | 1.193 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals