Netgear PROSAFE WG302v2 User Manual Page 63
- Page / 102
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
NETGEAR ProSafe 802.11g Wireless Access Point WG302v2 Reference Manual
Advanced Configuration 4-5
v1.0, May 2006
Table 4-1 describes the Advanced Wireless Parameters.
Modifying QoS Queue Parameters
Figure 4-3 also shows the Quality of Service (QoS) queue section on the Advanced Wireless
Settings page. For most networks, the default QoS queue parameter settings work well.Quality of
Service provides you with the ability to specify parameters on multiple queues for increased
throughput and better performance of differentiated wireless traffic, like Voice-over-IP (VoIP),
other types of audio, video, and streaming media, as well as traditional IP data.
The QoS options on the WG302v2 are as follows:
• Enable Wi-Fi Multimedia (WMM): Select Yes or No as required on the Advanced Wireless
Settings menu. The default is No.
WMM is a subset of the 802.11e standard. WMM allows wireless traffic to have a range of
priorities, depending on the kind of data. Time-dependent information, such as video or audio,
has a higher priority than normal traffic. For WMM to function correctly, wireless clients must
also support WMM. If WMM is disabled, you cannot configure Station EDCA parameters.
• SpectraLink Enabled: With SpectraLink enabled, SVP traffic takes priority over all other
traffic. The default is always enabled.
Table 4-1 Advanced Wireless LAN Parameters
Field Description
Enable SuperG Mode Click Enable to enable Super G Mode.
RTS Threshold The packet size used to determine whether the access point should use the
CSMA/CD (Carrier Sense Multiple Access with Collision Detection) or the
CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) mechanism
for packet transmission.
Fragmentation Length This is the maximum packet size used for fragmentation. Packets larger than
the size programmed in this field will be fragmented. The Fragment Threshold
value must be larger than the RTS Threshold value.
Beacon Interval Specifies the data beacon rate, which is between 20 and 1004.
DTIM Interval The Delivery Traffic Indication Message specifies the data beacon rate, which is
between 1 and 255.
Preamble Type A long transmit preamble may provide a more reliable connection or slightly
longer range. A short transmit preamble gives better performance.
Antenna Select the antenna to use for transmitting and receiving. The antennas are
labeled on the rear panel. The default is Auto.
- NETGEAR ProSafe 1
- 802.11g Wireless Access 1
- Point WG302v2 1
- Reference Manual 1
- Radio Frequency Notice 2
- FCC Statement 3
- Channels: 1 to 13 7
- Contents 9
- About This Manual 13
- How to Use This Manual 14
- How to Print this Manual 14
- About This Manual xv 15
- Chapter 1 17
- Introduction 17
- WG302v2 Key Features 18
- Introduction 1-3 19
- What’s In the Box? 20
- Hardware Description 21
- Rear Panel 22
- Chapter 2 23
- Figure 2-1 26
- Figure 2-2 27
- Figure 2-3 29
- Figure 2-4 29
- Basic IP Settings 30
- Wireless Settings 32
- Configuring Security Profiles 35
- Figure 2-7 36
- Profile Definition 37
- Network Authentication 37
- Data Encryption 38
- Figure 2-8 42
- Figure 2-9 44
- Chapter 3 45
- Management and Information 45
- Remote Management 46
- Figure 3-3 47
- CLI Commands 48
- Configuration File Management 49
- Erasing the Configuration 50
- Viewing General Information 51
- Viewing the Activity Log 53
- Figure 3-7 54
- Viewing Statistics 55
- Rogue AP Detection 56
- Figure 3-9 57
- Chapter 4 59
- Advanced Configuration 59
- 4-2 Advanced Configuration 60
- Configuring Hotspot Settings 61
- 4-4 Advanced Configuration 62
- Figure 4-3 62
- Advanced Configuration 4-5 63
- 4-6 Advanced Configuration 64
- Advanced Configuration 4-7 65
- 4-8 Advanced Configuration 66
- Figure 4-4 66
- Advanced Configuration 4-9 67
- Figure 4-5 67
- 4-10 Advanced Configuration 68
- Figure 4-6 68
- Advanced Configuration 4-11 69
- 4-12 Advanced Configuration 70
- Figure 4-7 70
- Advanced Configuration 4-13 71
- 4-14 Advanced Configuration 72
- Chapter 5 73
- Troubleshooting 73
- The LAN light is not lit 74
- Troubleshooting 5-3 75
- 5-4 Troubleshooting 76
- Appendix A 77
- Related Documents 77
- A-2 Related Documents 78
- Appendix B 79
- Specifications 79
- B-2 Specifications 80
- Specifications B-3 81
- B-4 Specifications 82
- Appendix C 83
- Command Line Reference 83
- Keyboard Shortcuts 84
- Interface Naming Conventions 85
- Entering CLI Commands 86
- Command Line Reference C-5 87
- Configuring Basic Settings 89
- Configuring Wireless Settings 90
- C-10 Command Line Reference 92
- Command Line Reference C-11 93
- RADIUS Server Settings 94
- Access Control 95
- C-14 Command Line Reference 96
- Table C-12 AP Management 96
- Command Line Reference C-15 97
- Table C-13 AP Information 97
- C-16 Command Line Reference 98
- Advanced Wireless Settings 99
- Hotspot Settings 99
- Command Line Reference C-19 101
- C-20 Command Line Reference 102
Related products and manuals for WLAN access points Netgear PROSAFE WG302v2
WLAN access points Netgear DG834G User Manual
(166 pages)
(166 pages)
WLAN access points Netgear WG102 User Manual
(134 pages)
(134 pages)
WLAN access points Netgear WNDAP330 User's Guide
(142 pages)
(142 pages)
© 2020, manymanuals.com. All rights reserved. | 1.696 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals