Netgear WNDAP350 User Manual Page 31
- Page / 136
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ProSafe Dual Band Wireless-N Access Point WNDAP350 Reference Manual
Basic Installation and Configuration 2-11
v1.1, November 2009
1. Disconnect the WNDAP350 and position it where it will be deployed. The best location is
elevated, such as wall mounted or on the top of a cubicle, at the center of your wireless
coverage area, and within line of sight of all the mobile devices.
2. Lift the antennae on either side so that they are vertical.
3. Connect an Ethernet cable from your WNDAP350 wirelss access point to a LAN port on your
router, switch, or hub.
4. Connect the power adapter to the wireless access point and plug the power adapter in to a
power outlet. The PWR, LAN, and Wireless LAN lights and should light up.
Verifying Wireless Connectivity
Using a computer with an 802.11b//jointfilesconvert/30164/bg/ng or 802.11a/na wireless adapter with the correct wireless
settings needed to connect to the WNDAP350 (SSID, WEP/WPA, MAC ACL, etc.), verify
connectivity by using a browser such as Mozilla Firefox or Internet Explorer to browse the
Internet, or check for file and printer access on your network.
The default SSID for the 802.11b//jointfilesconvert/30164/bg/ng wireless mode is NETGEAR_11g; the default SSID for
the 802.11a/na mode is NETGEAR_11a. The SSID of any wireless access adapters must match the
SSID configured in the ProSafe Dual Band Wireless-N Access Point WNDAP350. If they do not
match, no wireless connection will be made.
Note: Refer to the antenna positioning and wireless mode configuration information
in the Advanced Configuration chapter of the Reference Manual.
Note: By default, WNDAP350 is set with the DHCP client disabled. If your network
uses dynamic IP addresses, you must change this setting. To connect to the
WNDAP350 after the DHCP server on your network assigns it a new IP
address, enter the wireless access point name into your Web browser. The
default wireless access point name is netgearxxxxxx, where xxxxxx represents
the last 6 bytes of the MAC address. The default name is printed on the bottom
label of the WNDAP350.
Note: If you are unable to connect, see Chapter 5, “Troubleshooting and Debugging.”
- ProSafe Dual Band 1
- Wireless-N Access Point 1
- WNDAP350 Reference 1
- Industry Canada statements 6
- Contents 7
- About This Manual 11
- How to Print This Manual 12
- Revision History 12
- Chapter 1 13
- Introduction 13
- Key Features 14
- Introduction 1-3 15
- 1-4 Introduction 16
- System Requirements 17
- What’s In the Box? 18
- Hardware Description 18
- Front Panel 19
- Rear Panel 20
- Chapter 2 21
- Figure 2-1 23
- Figure 2-2 Login screen 25
- Figure 2-5 IP Settings 28
- Setting Basic IP Options 33
- Wireless Settings 34
- Setting up a Security Profile 51
- Configuring WEP 53
- Configuring WPA with RADIUS 55
- Configuring WPA2 with RADIUS 57
- Configuring WPA-PSK 60
- Configuring WPA2-PSK 61
- Chapter 3 67
- Management 67
- 3-2 Management 68
- Remote Console 69
- CLI Commands 70
- Management 3-5 71
- Configuration File Management 72
- Restoring Saved Settings 73
- 3-8 Management 74
- Management 3-9 75
- 3-10 Management 76
- Enabling the SysLog Server 77
- 3-12 Management 78
- Appendix B, “Related 79
- Documents.) 79
- 3-14 Management 80
- Management 3-15 81
- Table 3-2. Statistics Fields 81
- 3-16 Management 82
- Enabling Rogue AP Detection 83
- 3-18 Management 84
- Viewing Rogue AP Statistics 85
- 3-20 Management 86
- Figure 3-15 Unknown APs list 86
- Packet Capture 87
- 3-22 Management 88
- Chapter 4 89
- Advanced Configuration 89
- 4-2 Advanced Configuration 90
- Hotspot Settings 91
- 4-4 Advanced Configuration 92
- Advanced Configuration 4-5 93
- 4-6 Advanced Configuration 94
- Advanced Configuration 4-7 95
- 4-8 Advanced Configuration 96
- Advanced Configuration 4-9 97
- Enabling Wireless Bridging 98
- Advanced Configuration 4-11 99
- 4-12 Advanced Configuration 100
- Advanced Configuration 4-13 101
- 4-14 Advanced Configuration 102
- Advanced Configuration 4-15 103
- 4-16 Advanced Configuration 104
- Troubleshooting and Debugging 105
- Chapter 5 105
- The LAN light is not lit 106
- Appendix A 109
- Technical Specifications 111
- Appendix B 113
- Related Documents 113
- B-2 Related Documents 114
- Appendix C 115
- Command Line Reference 115
- C-2 Command Line Reference 116
- Command Line Reference C-3 117
- C-4 Command Line Reference 118
- Command Line Reference C-5 119
- C-6 Command Line Reference 120
- Command Line Reference C-7 121
- C-8 Command Line Reference 122
- Command Line Reference C-9 123
- C-10 Command Line Reference 124
- Command Line Reference C-11 125
- C-12 Command Line Reference 126
- Command Line Reference C-13 127
- C-14 Command Line Reference 128
- Numerics 129
Related products and manuals for WLAN access points Netgear WNDAP350
WLAN access points Netgear ME101 User Manual
(23 pages)
(23 pages)
WLAN access points Netgear WNAP320 User's Guide
(126 pages)
(126 pages)
WLAN access points Netgear WNDAP620 User Manual
(172 pages)
(172 pages)
WLAN access points Netgear WN604 User Manual
(70 pages)
(70 pages)
WLAN access points Netgear WAG102 User Manual
(102 pages)
(102 pages)
WLAN access points Netgear WGR614 v4 User Manual
(152 pages)
(152 pages)
WLAN access points Netgear MA101 User Manual
(67 pages)
(67 pages)
© 2020, manymanuals.com. All rights reserved. | 0.081 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals