Netgear WNDAP380Rv2 User Manual Page 132
- Page / 152
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Command-Line Reference
132
ProSAFE Dual Band Wireless-N Access Point with RFID Support, WNDAP380R
| |-no> --Reset
| | |-dhcp> --DHCP server settings
| | | |-dns1 --DNS1 server
| | | |-dns2 --DNS2 server
| | | |-wins1 --WINS1 server
| | | |-wins2 --WINS1 server
| | |-radius> --Radius server setting
| |
| | | |-primary> --Primary server
| | | | |-auth port --Authentication port
| | | | |-acct port --Accounting port
| | | | |-auth server --Authentication server
| | | | |-acct server --Accounting server
|
| | |-secondary> --Secondary server
| | | | |-auth port --Authentication port
| | | | |-acct port --Accounting port
| | | | |-auth server --Authentication server
| | | | |-acct server --Accounting server|
| |-radio> --Wireless LAN interface setting
| | |-2.4 --2.4 GHz wireless LAN status
| | |-2.4> --2.4 GHz wireless LAN interface setting
| | | |-80211d --802.11d enable
| | | |-aggregation-length --Aggregated packet size
| | | |-ampdu --Aggregated
MAC Protocol Data Unit
| | | |-beacon-interval --Wireless beacon period in TU(1024 us)
| | | |-channel --Wireless channel (depends on country
| | | | and wireless mode)
| | | |-channel auto --Set wireless channel to auto mode
| | | |-channel-width --Wireless channel width
| | | |-client-isolation --Client isolation status
| | | |-data-rate --Wireless transmission date rate
| | | |-dtim --Wireless DTIM period in beacon interval
| |
| |-fragmentation-length --Wireless fragmentation threshold
| | | |-guard-interval --Interval (from interference from other
| | | | transmissions)
| | | |-macacl add --Add wireless access control (ACL)
| | | |-macacl del --Delete wireless access control (ACL)
| | | |-macacl del all --Delete wireless access control (ACL)
| | | | Database
| | | |-max-client --Maximum client
| | | |-power --Output power
| | | |-preamble-type --Wireless preamble (only effect on
| |
| | 802.11b rates)
| | | |-rifs-transmission --Enable successive frame transmission
| | | | at different transmit
| | | |-rogue-ap-detection --Enable rogue access point detection
| | | |-rogue-ap-detection knownap add --Add rogue access point detection
| | | |-rogue-ap-detection knownap del MAC --Delete
rogue access point detection
- ProSAFE Dual Band Wireless-N 1
- WNDAP380R 1
- Trademarks 2
- Revision History 2
- Contents 3
- Chapter 4 Management 4
- Chapter 6 Monitoring 4
- Chapter 7 Troubleshooting 5
- What Is in the Box? 7
- System Requirements 8
- Key Features and Standards 8
- Key Features 9
- Networking 10
- Hardware Description 11
- Rear Panel 12
- Introduction 13
- Installation and Basic 14
- Configuration 14
- Ethernet Cabling Requirements 16
- Web Management Interface 19
- To configure time settings: 20
- Configure the IP Settings 21
- Ceiling Installation 31
- Wall Installation 35
- Desk Installation 38
- Wireless Configuration and 39
- Security 39
- Security Profiles 42
- Security Profile Concepts 43
- Form for 802.11b/bg/ng Modes 44
- Form for 802.11a/an Modes 45
- Configure Legacy 802.1X 52
- Figure 11. Legacy 802.1X 53
- Figure 12. WPA with RADIUS 53
- Figure 13. WPA2 with RADIUS 53
- Figure 15. WPA-PSK 54
- Figure 16. WPA2-PSK 54
- Management 63
- Enable Remote Management 64
- Web Browser Upgrade Procedure 67
- TFTP Server Upgrade Procedure 68
- Defaults 69
- Restore the Configuration 70
- Settings 70
- Default Configuration 72
- Enable the Syslog Server 73
- To enable a syslog server: 74
- To configure STP and VLANs: 80
- Configure Hotspot Settings 81
- To set up a hotspot server: 82
- To configure advanced QoS: 86
- 4. Click Apply 87
- Configure Wireless Bridging 88
- Advanced Configuration 100
- Configure RFID Settings 103
- To reboot the RFID module: 106
- To reset the RFID module: 106
- 3. Click Apply 107
- Monitoring 108
- View System Information 109
- Monitor Wireless Clients 111
- View the Activity Log 113
- Traffic Statistics 114
- Troubleshooting 116
- Basic Functioning 117
- Wireless-Capable Computer 118
- Check these items: 119
- Request timed out 121
- Problems with Date and Time 122
- Troubleshoot the RFID Module 122
- Supplemental Information 124
- Technical Specifications 125
- Factory Default Settings 127
- Command-Line Reference 131
- Numerics 147
Related products and manuals for WLAN access points Netgear WNDAP380Rv2
(28 pages)
WLAN access points Netgear WGR614 v5 User Manual
(172 pages)
(172 pages)
(43 pages)
WLAN access points Netgear WG602v3 User Manual
(122 pages)
(122 pages)
WLAN access points Netgear WG102 User Manual
(110 pages)
(110 pages)
WLAN access points Netgear MR814v2 User Manual
(142 pages)
(142 pages)
© 2020, manymanuals.com. All rights reserved. | 3.913 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals