Netgear WNDAP380Rv2 User Manual Page 24
- Page / 152
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installation and Basic Configuration
24
ProSAFE Dual Band Wireless-N Access Point with RFID Support, WNDAP380R
2. Configure the settings as explained in the following table:
Setting Description
Select the Enable radio button to enable the DHCP server. Use the default settings or specify the pool of IP
addresses to be assigned by setting the starting IP address and ending IP address. These addresses
should be part of the same IP address subnet as the wireless access point’
s LAN IP address.
DHCP Server VLAN ID Enter the VLAN ID for the DHCP server. The VLAN ID range is from 1 to 4094.
The default VLAN is 1.
Starting IP Address Enter the first address in the range of IP addresses to be assigned to DHCP
clients.
The default address is 192.168.1.02.
Ending IP Address Enter the last address in the range of IP addresses to be assigned to DHCP
clients. The default address is 192.168.1.50.
Subnet Mask Enter the subnet mask to be used by DHCP clients. The default mask is
255.255.255.0.
Gateway IP
Address Enter the IP address of the default routing gateway to be used by DHCP clients.
The default address is 192.168.0.1.
Primary DNS Address Enter the IP address of the primary Domain Name System (DNS) server
available to DHCP clients.
Secondary DNS Address Enter the IP address of the secondary DNS server available to DHCP clients.
Primary WINS Server Enter the IP address of the primary WINS server for the network, if there is any.
Secondary WINS Server Enter the IP address of the secondary WINS server for the network, if there is
any
.
Lease Enter the period that the DHCP server grants to DHCP clients to use the
assigned IP addresses. The default time is one day
.
3. Click Apply.
Configure the Basic Wireless Settings
For proper compliance and compatibility between similar products in your coverage area, you
need to configure the 802.11b/g/n and 802.11a/n wireless adapter settings correctly, including
the operating channel and country. You also need to configure the basic wireless network
settings for wireless devices to connect to your network. For other wireless features,
including wireless security, see Chapter 3, Wireless Configuration and Security.
- ProSAFE Dual Band Wireless-N 1
- WNDAP380R 1
- Trademarks 2
- Revision History 2
- Contents 3
- Chapter 4 Management 4
- Chapter 6 Monitoring 4
- Chapter 7 Troubleshooting 5
- What Is in the Box? 7
- System Requirements 8
- Key Features and Standards 8
- Key Features 9
- Networking 10
- Hardware Description 11
- Rear Panel 12
- Introduction 13
- Installation and Basic 14
- Configuration 14
- Ethernet Cabling Requirements 16
- Web Management Interface 19
- To configure time settings: 20
- Configure the IP Settings 21
- Ceiling Installation 31
- Wall Installation 35
- Desk Installation 38
- Wireless Configuration and 39
- Security 39
- Security Profiles 42
- Security Profile Concepts 43
- Form for 802.11b/bg/ng Modes 44
- Form for 802.11a/an Modes 45
- Configure Legacy 802.1X 52
- Figure 11. Legacy 802.1X 53
- Figure 12. WPA with RADIUS 53
- Figure 13. WPA2 with RADIUS 53
- Figure 15. WPA-PSK 54
- Figure 16. WPA2-PSK 54
- Management 63
- Enable Remote Management 64
- Web Browser Upgrade Procedure 67
- TFTP Server Upgrade Procedure 68
- Defaults 69
- Restore the Configuration 70
- Settings 70
- Default Configuration 72
- Enable the Syslog Server 73
- To enable a syslog server: 74
- To configure STP and VLANs: 80
- Configure Hotspot Settings 81
- To set up a hotspot server: 82
- To configure advanced QoS: 86
- 4. Click Apply 87
- Configure Wireless Bridging 88
- Advanced Configuration 100
- Configure RFID Settings 103
- To reboot the RFID module: 106
- To reset the RFID module: 106
- 3. Click Apply 107
- Monitoring 108
- View System Information 109
- Monitor Wireless Clients 111
- View the Activity Log 113
- Traffic Statistics 114
- Troubleshooting 116
- Basic Functioning 117
- Wireless-Capable Computer 118
- Check these items: 119
- Request timed out 121
- Problems with Date and Time 122
- Troubleshoot the RFID Module 122
- Supplemental Information 124
- Technical Specifications 125
- Factory Default Settings 127
- Command-Line Reference 131
- Numerics 147
Related products and manuals for WLAN access points Netgear WNDAP380Rv2
(28 pages)
WLAN access points Netgear WGR614 v5 User Manual
(172 pages)
(172 pages)
(43 pages)
WLAN access points Netgear WG602v3 User Manual
(122 pages)
(122 pages)
WLAN access points Netgear WG102 User Manual
(110 pages)
(110 pages)
WLAN access points Netgear MR814v2 User Manual
(142 pages)
(142 pages)
© 2020, manymanuals.com. All rights reserved. | 1.443 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals