Netgear WC7520 User Manual Page 196
- Page / 213
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Troubleshooting
196
ProSafe 20-AP Wireless Controller WC7520
Note: If your PC’s IP address is shown as 169.254.x.x:
Windows and Mac operating systems generate and assign an IP
address if the computer cannot reach a DHCP server. These
autogenerated addresses are in the range of 169.254.x.x. If your IP
address is in this range, check the connection from the PC to the
wireless controller and reboot your PC.
• If the wireless controller’s IP address has been changed and you do not know the current
IP address, reset the wireless controller’s configuration to factory default settings. This
sets the wireless controller’s IP address to 192.168.0.250. This procedure is explained in
Reboot or Reset the Wireless Controller on p
age 139.
Note: If you do not want to revert to the factory default settings and lose
your configuration settings, you can reboot the wireless controller
and use a sniffer to capture packets sent during the reboot. Look at
the ARP packets to locate the wireless controller’s LAN interface
address.
Internet Browser
• Make sure that you are using the http://address login rather than the https://address login.
• Make
sure that your browser has Java, JavaScript, or ActiveX enabled. If you are using
Internet Explorer, click Refresh to be sure that the Java applet is loaded.
• T
ry quitting the browser and launching it again.
• Make sure
that you are using the correct login information. The factory default login name
is admin, and the password is password. Make sure that Caps Lock is off when entering
this information.
If the wireless controller does not save changes you have made in the web management
inte
rface, check the following:
• W
hen entering configuration settings, be sure to click the Apply button before moving to
another tab or screen, or your changes are lost.
• Click the Refresh or Reload
button in your web browser. The changes might have
occurred, but the web browser might be caching the old configuration.
After you have upgraded the firmware, if the browser does not display the latest features of
the web
management interface, clear the browser’s cache, and refresh the screen.
- ProSafe 20-AP Wireless 1
- Controller WC7520 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Table of Contents 4
- Chapter 12 Troubleshooting 7
- Introduction and Overview 10
- Package Contents 11
- Hardware Features 12
- Rear Panel Features 13
- Figure 3 14
- NETGEAR ProSafe Access Points 15
- Plan a Wireless Network 16
- Firmware 16
- Organize the Network 16
- Licenses 18
- Maintenance and Support 18
- Figure 4 19
- Figure 5 21
- Figure 6 21
- Basic and Advanced Settings 22
- Profile Groups 23
- Advanced Profile 24
- Figure 9 25
- Scenarios 27
- DHCP Server 29
- Figure 10 33
- Deployment Scenarios 34
- Prerequisites 36
- RF Planning 41
- To define a building: 42
- Figure 14 43
- Figure 15 43
- To edit a building: 44
- To delete a building: 45
- Figure 16 45
- Figure 17 47
- Figure 18 48
- Figure 19 49
- Access Point Discovery and 51
- Management 51
- Limitations after Discovery 53
- Run the Discovery Wizard 54
- Figure 21 55
- Figure 22 55
- Discovery Results 56
- Manage the Access Point List 57
- Item Description 58
- Figure 26 60
- Configuring Network Settings 63
- Time Management 64
- Figure 29 65
- Table 9. Time settings 65
- Management VLANs 66
- Manage the DHCP Server 67
- 2. Click Add 68
- To edit a DHCP server: 69
- To delete a DHCP server: 69
- Manage Certificates 70
- Configure Syslog Settings 71
- To configure alarm actions: 72
- Figure 34 72
- 3. Click App 73
- Small WLAN Networks 75
- Larger WLAN Networks 75
- Profile Naming Conventions 76
- Figure 36 77
- Figure 37 78
- Figure 38 84
- Setting Description 85
- Figure 39 86
- Figure 40 86
- Figure 41 88
- Configurations 90
- Configure the Radio 91
- Figure 43 92
- Configure Wireless Settings 93
- Table 20. Wireless settings 94
- Figure 45 97
- Configure Channels 99
- Allocation screen displays: 100
- Specify RF Management 101
- Basic RF Management 102
- Figure 47 103
- Figure 48 104
- Figure 49 106
- Configure Load Balancing 107
- Figure 50 108
- Configure Rate Limiting 109
- Figure 51 110
- Figure 52 110
- Security 112
- Manage Rogue Access Points 113
- Figure 53 114
- Figure 54 116
- To use an external ACL: 118
- Figure 55 119
- Figure 56 121
- Server Groups 122
- Figure 57 123
- 4. Click Apply to save 124
- Figure 58 125
- Manage Guest Network Access 126
- Figure 59 127
- Table 29. Portal settings 128
- Figure 60 129
- Figure 61 130
- Figure 62 130
- Figure 63 130
- 4. Conf 131
- 6. Click Clo 133
- Maintaining the Controller 135
- Figure 64 136
- To upgrade the firmware: 137
- Figure 65 137
- 5. Click Apply 138
- Figure 66 140
- Reboot Access Points 141
- Manage External Storage 141
- Manage Remote Access 142
- Figure 69 143
- Table 32. SNMP settings 143
- Specify Session Time-Outs 144
- Save the Logs 144
- View Alerts and Events 145
- To view system alerts: 146
- Figure 73 146
- To view RF events: 146
- Figure 74 147
- Figure 75 147
- Figure 76 148
- Figure 77 148
- Figure 78 148
- Manage Licenses 149
- 1. Select Ma 150
- Settings screen displays: 150
- Register Your Licenses 151
- Figure 81 152
- Retrieve Your Licenses 153
- Manage Stacking 154
- Configure Stacking 155
- Figure 83 156
- Figure 84 156
- Table 35. Stacking settings 156
- Controller Selection List 157
- Manage Redundancy 158
- Figure 87 159
- N:1 Redundancy 160
- Figure 90 162
- Figure 91 163
- Figure 92 163
- Configure Redundancy 164
- Components 167
- To monitor the network: 168
- Figure 94 168
- View Network Usage 170
- Figure 96 171
- Figure 99 174
- Figure 100 174
- View Clients in the Network 176
- Figure 102 177
- Figure 103 178
- Figure 104 180
- Figure 105 182
- Figure 108 184
- Figure 109 184
- Figure 110 185
- Figure 111 187
- Figure 112 188
- To view the guest list: 189
- Figure 113 189
- Figure 114 189
- Monitor the SSIDs 190
- Monitor the Clients 191
- View Blacklisted Clients 192
- To export the list of blac 193
- Troubleshooting 194
- Test LED Never Turns Off 195
- LAN Port LEDs Not On 195
- Ethernet Cabling 195
- IP Address Configuration 195
- Internet Browser 196
- Request timed out 197
- Problems with Date and Time 198
- Problems with Access Points 198
- Connection Problems 199
- To ping an access point: 200
- Figure 119 200
- Figure 120 201
- Specifications 202
- WC7520 data sheet at 203
- Notification of Compliance 205
- GPL License Agreement 207
- Numerics 208
Related products and manuals for Networking Netgear WC7520
Networking Netgear DG834GSP User Manual
(32 pages)
(32 pages)
Networking Netgear ProSafe FS728TP User Manual
(248 pages)
(248 pages)
Networking Netgear 3G User Manual
(106 pages)
(106 pages)
Networking Netgear 7000 Series User Manual
(220 pages)
(220 pages)
Networking Netgear 724TP User Manual
(2 pages)
(2 pages)
Networking Netgear ProSafe SSL312 User Manual
(122 pages)
(122 pages)
Networking Netgear MA401 User Manual
(84 pages)
(84 pages)
Networking Netgear DG834GUV5 User Manual
(120 pages)
(120 pages)
Networking Netgear WMS5316 User Manual
(66 pages)
(66 pages)
(2 pages)
Networking Netgear MA111v2 User's Guide
(83 pages)
(83 pages)
Networking Netgear STM300EW-100NAS User Manual
(254 pages)
(254 pages)
Networking Netgear 782S Quick Start Guide
(48 pages)
(48 pages)
Networking Netgear Switch M4100 User Manual
(559 pages)
(559 pages)
Networking Netgear DG834G User Manual
(190 pages)
(190 pages)
Networking Netgear WPNT121 User's Guide
(48 pages)
(48 pages)
Networking Netgear Music Player User Manual
(70 pages)
(70 pages)
© 2020, manymanuals.com. All rights reserved. | 0.144 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals