Netgear RANGEMAX WAG302 User Manual Page 17
- Page / 120
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302
Introduction 2-3
202-10078-01
• Access Control. The Access Control MAC address filtering feature can ensure that only
trusted wireless stations can use the WAG302 to gain access to your LAN.
• Simple Configuration. If the default settings are unsuitable, they are easy to change.
• Hidden Mode. The SSID is not broadcast, assuring only clients configured with the correct
SSID can connect.
• Secure Telnet Command Line Interface. The Telnet command line interface enables direct
access over the serial port and easy scripting of configuration of multiple WAG302 across an
extensive network via the Ethernet interface. An SSH client is required.
• Configuration Backup. Configuration settings can be backed up to a file and restored.
• Secure and Economical Operation. Adjustable power output allows more secure or
economical operation.
• Power over Ethernet. Power can be supplied to the WAG302 over the Ethernet port from any
802.3af compliant mid-span or end-span source such as the NETGEAR FSM7326P Managed
Power over Ethernet Layer 3 managed switch.
• Autosensing Ethernet Connection with
Auto Uplink Interface. Connects to 10/100 Mbps
IEEE 802.3 Ethernet networks.
• LED Indicators. Power, test, LAN speed, LAN activity, and wireless activity are easily
identified.
AutoCell—The Self-Organizing Wireless Network
AutoCell
TM
, an embedded control system for 802.11 WLANs. AutoCell increases available
bandwidth and reduces WLAN installation and operating costs significantly.
AutoCell is completely automatic: It is a continuous communication system that relies on a
lightweight protocol to monitor changes on the wireless domain while keeping overhead very low.
Among AutoCell's inherent advantages:
• Elimination of manual site surveys and channel maps
• Dynamic load balancing
• Plug-and-play-implementation
• Transparent fault recovery and failover
Since AutoCell is completely self-organizing, it holds human intervention to a minimum. That
reduces the people costs associated with deployment, management, and maintenance—making
802.11 WLANs practical, efficient, and cost-effective.
- Reference Manual for the 1
- NETGEAR ProSafe Dual Band 1
- Wireless Access Point 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Radio Frequency Notice 3
- DECLARATION OF CONFORMITY 4
- Contents 7
- Chapter 1 11
- About This Manual 11
- How to Use This Manual 12
- How to Print this Manual 13
- 1-4 About This Manual 14
- Chapter 2 15
- Introduction 15
- Key Features 16
- Introduction 2-3 17
- 2-4 Introduction 18
- System Requirements 19
- What’s In the Box? 19
- Hardware Description 20
- Rear Panel 21
- 2-8 Introduction 22
- Chapter 3 23
- Cabling Requirements 24
- Default Factory Settings 25
- 6HFXULW\2SWLRQV 26
- 5DQJH8SWR)RRW5DGLXV 26
- ET UP THE WAG302 ACCESS POINT 27
- Figure 3-2: Login window 28
- 4VERIFY WIRELESS CONNECTIVITY 33
- Wireless Settings 11a 35
- Wireless Settings 11b/g 37
- How to Configure WEP 46
- How to Configure WPA-PSK 51
- Figure 3-16: IP Settings menu 52
- Chapter 4 55
- Management 55
- CLI Commands 57
- 4-4 Management 58
- General Information 59
- 4-6 Management 60
- Management 4-7 61
- Statistics 62
- Management 4-9 63
- Configuration File Management 64
- Management 4-11 65
- Rebooting the Access Point 66
- 4-14 Management 68
- Chapter 5 69
- Advanced Configuration 69
- 5-2 Advanced Configuration 70
- Advanced Configuration 5-3 71
- AutoCell RF Management 72
- Advanced Configuration 5-5 73
- 5-6 Advanced Configuration 74
- Advanced Configuration 5-7 75
- 5-8 Advanced Configuration 76
- Advanced Configuration 5-9 77
- Hub or Switch 78
- 192.168.0.1 79
- 5-12 Advanced Configuration 80
- Segment 1 81
- 5-14 Advanced Configuration 82
- Chapter 6 83
- Troubleshooting 83
- The LAN light is not lit 84
- Troubleshooting 6-3 85
- Appendix A 87
- Specifications 87
- A-2 Specifications 88
- Appendix B 89
- Wireless Networking Basics 89
- 802.11 Authentication 91
- Open System Authentication 92
- Shared Key Authentication 92
- Overview of WEP Parameters 93
- Key Size 94
- Wireless Channels 95
- 802.11a Wireless Channels 97
- WPA Wireless Security 98
- How Does WPA Compare to WEP? 99
- 202-10078-01 100
- Wired Network with Optional 102
- 802.1x Port Based Network 102
- Access Control 102
- Wireless LAN 102
- Product Support for WPA 106
- Is WPA Perfect? 106
- Appendix C 109
- Command Line Reference 109
- C-2 Command Line Reference 110
- Command Line Reference C-3 111
- C-4 Command Line Reference 112
- Glossary 113
- Wireless Network Name (SSID) 119
- -8 Glossary 120
Related products and manuals for WLAN access points Netgear RANGEMAX WAG302
WLAN access points Netgear WNAP320 User's Guide
(126 pages)
(126 pages)
WLAN access points Netgear WNDAP620 User Manual
(172 pages)
(172 pages)
WLAN access points Netgear WN604 User Manual
(70 pages)
(70 pages)
WLAN access points Netgear WAG102 User Manual
(102 pages)
(102 pages)
WLAN access points Netgear WGR614 v4 User Manual
(152 pages)
(152 pages)
WLAN access points Netgear MA101 User Manual
(67 pages)
(67 pages)
WLAN access points Netgear 802.11g User Manual
(108 pages)
(108 pages)
WLAN access points Netgear WG602v2 User's Guide
(122 pages)
(122 pages)
© 2020, manymanuals.com. All rights reserved. | 0.873 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals