Netgear WG102 User Manual Page 118
- Page / 134
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
118 |
WG102-500, WGAP150 ProSafe™ 802.11g Wireless Access Point
3. From the Method pull-down menu, select Ping. The screen expands, enabling you to
configure ping fields.
4. Specify the fields that are explained in the following table.
Table 6-1. Health Check Settings
Field Description
Ping Host The IP address of the host to which the continuous ping should be sent. By default,
the IP address of the default gateway that you selected in “Configuring IP Settings”
on page 20 is used as the ping host, and the Ping Host field is masked out.
Deselect the Use default gateway as Ping Host checkbox to specify a host in the
Ping Host field.
Interval The interval in seconds at which the host is pinged. You can select 10 (default), 30,
60, or 120 seconds.
Retries The number of times that the wireless access point attempts to ping the host after
the initial attempt fails. You can select 1, 3 (default), 5, or 7. If all pings fail, the
connection between the wireless access point and the host is terminated, and the
Event Log will show the message “Health Check: Link Down.” If the connection
comes up again, the Event Log will show the message “Health Check: Link Up.”
5. Click Save or Save to Flash & Activate to save your settings.
Using the Ping, Traceroute, and NsLookup Utility
These diagnostic tools are not required if the wireless access point functions normally. As
port of a troubleshooting procedure, you can send a ping packet, traceroute, or Nslookup
request to an IP address or host name.
To use diagnostic tools:
1. Log in to the wireless access point at its default LAN address of http://192.168.0.229
with its default user name of admin and default password of password, or using
whatever LAN address, user name, and password you have chosen for the wireless
access point.
- WG102-500, WGAP150 1
- ProSafe™ 802.11g Wireless 1
- Access Point 1
- Technical Support 2
- Trademarks 2
- Statement of Conditions 2
- Revision History 2
- Table of Contents 3
- 4 4
- Table of Contents 5
- Chapter 6 Troubleshooting 6
- Appendix B Related Documents 6
- Introduction 7
- Key Features 8
- 9
- System Requirements 10
- What’s In the Box? 10
- Hardware Description 11
- Table 1-1 12
- 13
- Ethernet Cabling Requirements 14
- 15
- Figure 2-1 16
- Figure 2-2 17
- Figure 2-3 17
- Web Interface Menu 18
- Settings 18
- System > Basic 19
- Configuring IP Settings 20
- Figure 2-7 21
- Table 2-3. PPPoE Settings 22
- Figure 2-8 22
- Configuring LAN Settings 23
- 24 24
- Figure 2-10 25
- 26 26
- Figure 2-11 27
- Figure 2-12 28
- 29
- 30 30
- 31
- 32 32
- 33
- Figure 3-1 34
- Security Profiles 35
- 36 36
- 37
- Figure 3-2 38
- Figure 3-3 39
- Configuring Static WEP 40
- Table 3-3 41
- Figure 3-5 41
- Table 3-2 41
- Table 3-4 42
- Figure 3-6 42
- Table 3-5 43
- Figure 3-7 43
- Figure 3-8 44
- Table 3-6 44
- Table 3-6 45
- Figure 3-9 46
- 47
- 48 48
- WAPI Certificates 49
- Figure 3-11 50
- Figure 3-12 51
- Figure 3-13 52
- Figure 3-14 53
- Figure 3-15 54
- Figure 3-16 55
- Table 3-9. Filter Settings 56
- Figure 3-17 57
- Figure 3-18 58
- Figure 3-19 59
- 60 60
- Managing Your Network 61
- Backing up the Configuration 62
- Restoring the Configuration 62
- 63
- Figure 4-2 64
- 65
- Figure 4-3 66
- Figure 4-4 67
- Viewing the Activity Log 68
- Figure 4-6 69
- Figure 4-7 69
- Viewing System Information 70
- Figure 4-8 71
- Table 4-1 71
- Table 4-1 72
- Table 4-2 73
- Figure 4-9 73
- Viewing Wireless Information 74
- Table 4-4 75
- Figure 4-11 75
- Figure 4-12 75
- Table 4-5 76
- Figure 4-13 77
- Configuring Remote Management 78
- Table 4-7 79
- 80 80
- Figure 4-15 81
- Figure 4-16 82
- Figure 4-17 83
- 84 84
- SNMP Remote Management 85
- Configuring SNMP Communities 86
- Figure 4-20 87
- Figure 4-21 87
- Configuring SNMP Users 88
- Figure 4-22 89
- Figure 4-23 89
- Configuring TR069 Operation 90
- Scheduling Management Tasks 91
- Figure 4-25 92
- 93
- 94 94
- Advanced Configuration 95
- Figure 5-1 96
- Figure 5-2 97
- 98 98
- Figure 5-3 99
- 100 100
- Figure 5-4 101
- Figure 5-5 102
- Figure 5-6 103
- 104 104
- Figure 5-7 105
- Figure 5-8 106
- 107
- Configuring Repeater Mode 108
- 109
- 110 110
- Troubleshooting 111
- Basic Functioning 112
- Wireless-Capable Computer 113
- 114 114
- 115
- Problems with Date and Time 116
- Using the Diagnostic Tools 117
- 118 118
- Downloading Debug Information 119
- Figure 6-3 120
- Technical Specifications 121
- Default Factory Settings 122
- Table 0-1 123
- 124 124
- Related Documents 125
- 126 126
- Numerics 127
- 128 128
- Index 129
- 130 130
- Index 131
- 132 132
- Index 133
- 134 134
Related products and manuals for WLAN access points Netgear WG102
WLAN access points Netgear WNDAP330 User's Guide
(142 pages)
(142 pages)
© 2020, manymanuals.com. All rights reserved. | 0.691 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals