Netgear WC7600 User Manual Page 13
- Page / 307
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Introduction
13
ProSAFE Wireless Controller WC7600
From left to right, the wireless controller’s front panel shows the following counter, LEDs,
button, ports, and slots:
• Digital counter. Displays the number of connected access points that are in a healthy
state.
• From top to bottom:
- Power LED
- Status LED
- Fan LED
- Stack Master LED
These LEDs are described in Table 1 on page 13.
• Reset button. Using a sharp object, press and hold this button for about 10 seconds until
the Status LED flashes and the wireless controller returns to factory default settings. If
you reset the wireless controller, all configuration settings are lost and the default
password is restored.
• USB port. Allows for external storage for floor heat maps, which will be supported in a
future release.
• SFP slots. Two SFP slots for optional 10GE SFP+ or 1G SFP gigabit interface
converters (GBICs), each slot with an LED.
• Ethernet port. One 10/100/1000 Mbps LAN Ethernet port with an RJ-45 connector, left
LED, and right LED. The Ethernet port provides switched N-way, automatic speed
negotiating, auto MDI/MDIX technology.
• Console port. RS232 port for connecting to an optional console terminal. The port has a
DB9 male connector. The default baud rate is 9600 K. The configuration is 8 bits, no
parity, and 1 stop bit. The console port is for debugging under guidance of NETGEAR
technical support only.
The function of each LED is described in the following table:
Table 1. LED functions
LED Status Description
Power LED Green The green Power LED should be lit when the wireless controller is on.
Off If the power LED is not lit when the wireless controller is on, check the
connections and check to see if the power outlet is controlled by a wall
switch that is turned off (see
Power LED Is Not Lit on page 296).
Status LED Yellow The wireless controller is initializing. After approximately two minutes, when
the wireless controller has completed its initialization, the Status LED turns
green. If the Status LED remains yellow, the initialization has failed (see
Status LED Never Turns Off on page 296).
Green The wireless controller has completed its initialization successfully. The
Status LED should be steady green during normal operation.
- ProSAFE Wireless Controller 1
- Compliance 2
- Trademarks 2
- Chapter 1 Introduction 3
- Chapter 3 RF Planning 3
- Chapter 13 Troubleshooting 8
- Passwords Requirements 8
- Key Features and Capabilities 10
- Introduction 11
- Hardware Features 12
- Package Contents 12
- Table 1. LED functions 13
- Back Panel Features 14
- Figure 4. Product label 15
- NETGEAR ProSAFE Access Points 16
- Licenses 20
- Maintenance and Support 20
- Scenarios 21
- Profile Group Concepts 23
- Management VLAN 25
- Client VLANs 26
- DHCP Server 26
- RF Planning 41
- To define a building: 42
- Figure 12 43
- Figure 13 43
- To edit a building: 44
- To delete a building: 45
- Figure 14 46
- Figure 15 47
- Figure 16 49
- Figure 17 49
- Overview 51
- Manage the Time Settings 61
- Management VLAN Concepts 62
- Untagged VLAN Concepts 63
- Link Aggregation Concepts 63
- Manage the DHCP Server 65
- 5. Click the Add button 67
- Remove a DHCP Server 69
- Register Your Licenses 70
- To register your licenses: 72
- Manage Certificates 74
- Configure Syslog Settings 77
- To configure alarm actions: 79
- Manage Security Profiles and 82
- Profile Groups 82
- Small WLAN Networks 83
- Large WLAN Networks 84
- Profile Naming Conventions 84
- Add an Advanced Profile Group 91
- Server Groups 104
- Import a MAC List from a File 112
- 00:00:11:11:22:26 113
- 00:00:11:11:22:25 113
- Discover and Manage Access 119
- General Discovery Guidelines 120
- Layer 3 Discovery Guidelines 120
- Number of Controllers Octet 121
- 1 controller 02:04 121
- 2 controllers 02:08 121
- 3 controllers 02:0c 121
- Limitations after Discovery 122
- Points in a Layer 2 Subnet 123
- Manage the Managed AP List 131
- Item Description 132
- Manage Rogue Access Points 140
- Classify Rogue Access Points 142
- 00:00:11:11:22:29 144
- 00:00:11:11:22:28 144
- 00:00:11:11:22:27 144
- Manage Guest Network Access 145
- Configure a Portal 146
- 7. Click the Apply button 148
- User and Account Concepts 150
- Add a Management User 151
- Add a WiFi User 152
- Add a Captive Portal Account 154
- 6. Click the Add button 155
- Add a Captive Portal User 156
- Remove a User or Account 159
- Configure Wireless and QoS 161
- Settings 161
- Concepts 162
- Configure the Radio 162
- Configure Wireless Settings 165
- Profile Group 175
- Configure Channels 177
- Radio Frequency Concepts 180
- WLAN Healing Concepts 181
- Manage the Preferred Bands 186
- Quality of Service Concepts 188
- 8. Click the Apply button 191
- Manage Load Balancing 192
- Configure Load Balancing 193
- Manage Rate Limiting 194
- Manage the Configuration File 199
- Upgrade the Firmware 201
- Reset the Wireless Controller 205
- Manage External Storage 206
- Manage Remote Access 207
- 6. Click the Apply button 208
- Specify Session Time-Outs 209
- Manage the System Logs 209
- Query the System Logs 210
- Save the System Logs 212
- Clear the System Logs 212
- View Alerts and Events 213
- View Radio Frequency Events 214
- View Load-Balancing Events 215
- View Rate-Limit Events 217
- View Redundancy Events 218
- View Stacking Events 218
- Manage Licenses 219
- View Your Licenses 220
- Retrieve Your Licenses 222
- Reboot Access Points 223
- Setting Description 225
- The default number is 69 225
- Stacking Concepts 228
- Configure a Stack 230
- VRRP Redundancy Concepts 237
- Before failover 238
- After failover 239
- VRRP N:1 Redundancy Concepts 241
- Figure 24 243
- Figure 25 243
- Figure 26 244
- Change a Redundant Controller 246
- Remove a Redundancy Group 247
- Its Components 248
- Monitor the Network 249
- To view the Usage screen: 266
- To view the Clients screen: 273
- Does Not Manage 279
- Controller 282
- Wireless Controller Manages 283
- 10. Click the Cancel button 294
- Troubleshooting 295
- Power LED Is Not Lit 296
- Status LED Never Turns Off 296
- Check the Ethernet Cabling 297
- Check the Internet Browser 298
- Resolve Discovery Problems 300
- Resolve Connection Problems 300
- Ping an Access Point 301
- • Factory Default Settings 304
- • Technical Specifications 304
- • Password Requirements 304
- Factory Default Settings 305
- Technical Specifications 305
- Password Requirements 306
Related products and manuals for Networking Netgear WC7600
Networking Netgear WG111T User Manual
(49 pages)
(49 pages)
Networking Netgear 597E User's Guide
(49 pages)
(49 pages)
Networking Netgear WG511T User's Guide
(48 pages)
(48 pages)
Networking Netgear 597E User's Guide
(12 pages)
(12 pages)
Networking Netgear WC7520 User Manual
(213 pages)
(213 pages)
Networking Netgear DG834GSP User Manual
(32 pages)
(32 pages)
Networking Netgear ProSafe FS728TP User Manual
(248 pages)
(248 pages)
Networking Netgear 3G User Manual
(106 pages)
(106 pages)
Networking Netgear 7000 Series User Manual
(220 pages)
(220 pages)
Networking Netgear 724TP User Manual
(2 pages)
(2 pages)
Networking Netgear ProSafe SSL312 User Manual
(122 pages)
(122 pages)
Networking Netgear MA401 User Manual
(84 pages)
(84 pages)
Networking Netgear DG834GUV5 User Manual
(120 pages)
(120 pages)
Networking Netgear WMS5316 User Manual
(66 pages)
(66 pages)
(2 pages)
Networking Netgear MA111v2 User's Guide
(83 pages)
(83 pages)
Networking Netgear STM300EW-100NAS User Manual
(254 pages)
(254 pages)
Networking Netgear 782S Quick Start Guide
(48 pages)
(48 pages)
© 2020, manymanuals.com. All rights reserved. | 0.301 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals