Netgear WNDAP350 User's Guide Page 18
- Page / 138
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
ProSafe Dual Band Wireless N Access Point WNDAP350 Reference Manual
1-4 Introduction
v2.0, April 2013
• Wireless Multimedia (WMM) Support. WMM is a subset of the 802.11e standard. WMM
allows wireless traffic to have a range of priorities, depending on the kind of data. Time-
dependent information, like video or audio, has a higher priority than normal traffic. For
WMM to function correctly, Wireless clients must also support WMM.
• WMM Power Save Support. Power Save uses mechanisms from 802.11e and legacy 802.11
to save power (for battery powered equipment) and fine-tune power consumption.
• VLAN Security Profiles. Each Security Profile can be assigned a VLAN ID as each Security
Profile is modified.
802.11a/b/g/n Standards-based Wireless Networking
The ProSafe Dual Band Wireless N Access Point WNDAP350 provides a bridge between
Ethernet wired LANs and 802.11a/b/g/n compatible wireless LAN networks. It provides
connectivity between Ethernet wired networks and radio-equipped wireless notebook systems,
desktop systems, print servers, and other devices. Additionally, the WNDAP350 supports the
following wireless features:
• Aggregation Support
• Reduced Inter Frame Spacing support
• Multiple Input, Multiple Output (MIMO) support
• Distributed coordinated function (CSMA/CA, Back off procedure, ACK procedure,
retransmission of unacknowledged frames)
• RTS/CTS handshake
• Beacon generation
• Packet fragmentation and reassembly
• Auto or long preamble
• Roaming among access points on the same subnet
Autosensing Ethernet Connections with Auto Uplink
The WNDAP350 can connect to a standard Ethernet network. The LAN interface is autosensing
and capable of full-duplex or half-duplex operation.
The wireless access point incorporates Auto Uplink
TM
technology. The Ethernet port will
automatically sense whether the Ethernet cable plugged into the port should have a “normal”
connection such as to a computer or an “uplink” connection such as to a switch or hub. That port
will then configure itself to the correct configuration. This feature also eliminates any concerns
about crossover cables, as Auto Uplink will accommodate either type of cable to make the right
connection.
- ProSafe Dual Band 1
- Wireless N Access Point 1
- WNDAP350 Reference 1
- FCC Information to User 4
- FCC Declaration Of Conformity 5
- Contents 7
- About This Manual 11
- How to Print This Manual 12
- Revision History 12
- About This Manual xiii 13
- Chapter 1 15
- Introduction 15
- Key Features 16
- Introduction 1-3 17
- 1-4 Introduction 18
- System Requirements 19
- What’s In the Box? 20
- Hardware Description 20
- Front Panel 21
- Rear Panel 22
- Chapter 2 23
- Figure 2-1 25
- Figure 2-2 Login screen 27
- Figure 2-5 IP Settings 30
- Setting Basic IP Options 35
- Wireless Settings 36
- Setting up a Security Profile 53
- Configuring WEP 55
- Configuring WPA with RADIUS 57
- Configuring WPA2 with RADIUS 59
- Configuring WPA-PSK 62
- Configuring WPA2-PSK 63
- Chapter 3 69
- Management 69
- 3-2 Management 70
- Remote Console 71
- CLI Commands 72
- Management 3-5 73
- Configuration File Management 74
- Restoring Saved Settings 75
- 3-8 Management 76
- Management 3-9 77
- 3-10 Management 78
- Enabling the SysLog Server 79
- 3-12 Management 80
- Appendix B, “Related 81
- Documents.) 81
- 3-14 Management 82
- Management 3-15 83
- Table 3-2. Statistics Fields 83
- 3-16 Management 84
- Enabling Rogue AP Detection 85
- 3-18 Management 86
- Viewing Rogue AP Statistics 87
- 3-20 Management 88
- Figure 3-15 Unknown APs list 88
- Packet Capture 89
- 3-22 Management 90
- Chapter 4 91
- Advanced Configuration 91
- 4-2 Advanced Configuration 92
- Hotspot Settings 93
- 4-4 Advanced Configuration 94
- Advanced Configuration 4-5 95
- 4-6 Advanced Configuration 96
- Advanced Configuration 4-7 97
- 4-8 Advanced Configuration 98
- Advanced Configuration 4-9 99
- Enabling Wireless Bridging 100
- Advanced Configuration 4-11 101
- 4-12 Advanced Configuration 102
- Advanced Configuration 4-13 103
- 4-14 Advanced Configuration 104
- Advanced Configuration 4-15 105
- 4-16 Advanced Configuration 106
- Chapter 5 107
- Troubleshooting and Debugging 107
- The LAN light is not lit 108
- Appendix A 111
- Technical Specifications 113
- Appendix B 115
- Related Documents 115
- B-2 Related Documents 116
- Appendix C 2.0 117
- Command Line Reference 117
- Numerics 131
Related products and manuals for WLAN access points Netgear WNDAP350
WLAN access points Netgear WNDAP360 User Manual
(137 pages)
(137 pages)
WLAN access points Netgear DG834G User Manual
(166 pages)
(166 pages)
WLAN access points Netgear WG102 User Manual
(134 pages)
(134 pages)
WLAN access points Netgear WNDAP330 User's Guide
(142 pages)
(142 pages)
© 2020, manymanuals.com. All rights reserved. | 0.095 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals