Netgear WNDAP620 User Manual Page 117
- Page / 172
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Advanced Configuration
117
ProSafe Premium 3 x 3 Dual-Band Wireless-N Access Point WNDAP620
Note: Rate limiting for the wireless interface is an optional setting that
applies to all traffic on the wireless interface. Unlike classification
rate limiting, which you can specify for each classification, rate
limiting for the wireless interface needs to be specified only once.
To specify rate limiting for the wireless interface:
1. S
pecify rate limiting for the entire wireless interface as explained in the following table:
2. Click App
ly to save your settings.
To modify a QoS policy:
1. F
rom the Create Policy drop-down list, select the policy that you want to modify.
2. T
o delete a classification, select it in the Classification field, and click Delete Classification.
3. T
o add a classification, follow Step 5 through Step 7 in the procedure to configure a new
QoS policy. You can also change the name of the policy.
4. Click App
ly to save your settings.
To delete a QoS policy:
1. F
rom the Create Policy drop-down list, select the policy that you want to delete.
2. Click Dele
te Policy.
3. Click App
ly to save your settings.
Table 35. Wireless interface rate limiting settings
Setting Description
Interface
Rate Limiting
Bits Per Sec. Enter a value between 0 and 300,000,000 bps to specify the maximum
data rate up to which packets are queued for transmission and sent
immediately over the wireless interface. This value applies to all traffic
on the wireless interface.
Note: When the maximum rate is exceeded, packets are retained in
the que
ue and sent when the transmission falls below the maximum
rate again.
Burst Rate
(Bytes)
Enter a value between 0 and 37,500,000 bytes to specify the maximum
amou
nt of data that can be transmitted in a burst over the wireless
interface. This value applies to all traffic on the wireless interface.
- ProSafe Premium 3 x 3 1
- Dual-Band Wireless-N 1
- Access Point WNDAP620 1
- Trademarks 2
- Revision History 2
- Contents 3
- Chapter 6 Troubleshooting 5
- What Is in the Box? 7
- System Requirements 8
- Key Features and Standards 8
- Key Features 9
- Introduction 10
- Hardware Description 11
- Rear Panel 13
- Figure 3 14
- Figure 4 14
- 4. Click Regi 15
- 6. Click su 16
- Ethernet Cabling Requirements 18
- Figure 7 21
- Web Management Interface 22
- Figure 10 23
- Figure 11 23
- To configure time settings: 24
- Figure 12 24
- Configure the IPv4 Settings 25
- 3. Click Apply 26
- to save your settings 26
- Figure 14 27
- Figure 15 29
- Figure 16 32
- Ceiling Installation 35
- Wall Installation 38
- Desk Installation 41
- Figure 17 43
- Security Profiles 44
- Form for 802.11b/bg/ng Modes 46
- Form for 802.11a/an Modes 47
- Figure 18 48
- Figure 19 49
- Table 8. Profile settings 49
- Figure 20 50
- Figure 21 53
- Configure Legacy 802.1X 54
- Figure 23 55
- Figure 24 55
- Figure 25 55
- Figure 26 55
- Figure 27 56
- Figure 28 56
- Figure 29 57
- Figure 30 58
- Figure 31 60
- Figure 32 62
- Figure 33 63
- Management and Monitoring 64
- 3. Click App 65
- Figure 35 66
- Figure 36 67
- Web Browser Upgrade Procedure 68
- TFTP Server Upgrade Procedure 69
- Defaults 70
- Restore the Configuration 71
- Settings 71
- Figure 41 72
- Default Configuration 73
- Figure 43 74
- Manage User Accounts 75
- Enable the Syslog Server 76
- View System Information 77
- To view the System screen: 78
- Monitor Wireless Stations 80
- Figure 47 81
- Figure 48 81
- View the Activity Log 83
- Traffic Statistics 83
- Statistics screen: 84
- Figure 51 86
- Figure 52 87
- Figure 53 88
- Figure 54 94
- Most Recent Attacks 96
- Attack Counter 96
- Ad Hoc Networks 97
- Figure 58 98
- Figure 59 100
- Table 28. IPv6 settings 100
- Advanced Configuration 101
- Figure 60 102
- Link Layer Discovery Protocol 103
- To configure STP and VLANs: 104
- Figure 61 104
- Configure Ethernet LLDP 105
- Configure Hotspot Settings 106
- Figure 63 107
- 802.11a/na tab 108
- To configure advanced QoS: 110
- Figure 65 111
- Table 32. EDCA settings 111
- Figure 66 113
- To modify a QoS policy: 117
- To delete a QoS policy: 117
- Configure Wireless Bridging 118
- Figure 67 119
- Figure 68 119
- Figure 69 120
- Figure 70 122
- Figure 71 123
- Figure 72 123
- Figure 73 126
- Figure 74 127
- Figure 75 128
- Troubleshooting 131
- Basic Functioning 132
- Check these items: 133
- Wireless-Capable Computer 134
- Request timed out 136
- Problems with Date and Time 137
- Use the Packet Capture Tool 138
- Supplemental Information 139
- Factory Default Settings 142
- Command-Line Reference 146
- Notification of Compliance 161
- FCC Information to User 163
- FCC Declaration of Conformity 163
- FCC Caution 163
- Radiation Exposure Statement: 164
- Industry Canada 164
- Industrie Canada 164
- Avertissement 165
- Detachable Antenna Usage 165
- Numerics 166
Related products and manuals for WLAN access points Netgear WNDAP620
WLAN access points Netgear WN604 User Manual
(70 pages)
(70 pages)
WLAN access points Netgear WAG102 User Manual
(102 pages)
(102 pages)
WLAN access points Netgear WGR614 v4 User Manual
(152 pages)
(152 pages)
WLAN access points Netgear MA101 User Manual
(67 pages)
(67 pages)
WLAN access points Netgear 802.11g User Manual
(108 pages)
(108 pages)
WLAN access points Netgear WG602v2 User's Guide
(122 pages)
(122 pages)
WLAN access points Netgear ME102 User Manual
(17 pages)
(17 pages)
© 2020, manymanuals.com. All rights reserved. | 1.877 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals