Netgear FS728TP User Manual Page 116
- Page / 196
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
FS728TP Smart Switch Software User Manual
5-83 Configuring the Device Using Your Browser
v2.0, November 2006
– Hello Time – Specifies the device Hello Time. The Hello Time indicates the amount of
time in seconds a Root bridge. The device waits between configuration messages. The
default is 2 seconds.
– Max Age – Specifies the device Maximum Age Time. The Maximum Age Time is the
amount of time in seconds a bridge waits before sending configuration messages. The
default Maximum Age Time is 20 seconds.
– Forward Delay – Specifies the device Forward Delay Time. The Forward Delay Time is
the amount of time in seconds a bridge remains in a listening and learning state before
forwarding packets. The default is 15 seconds.
– Bridge ID – Identifies the Bridge priority and MAC address.
– Root Bridge ID –Identifies the Root Bridge priority and MAC address.
– Root Port –Indicates the port number that offers the lowest cost path from this bridge to
the Root Bridge. This field is significant when the bridge is not the Root Bridge. The
default is zero.
– Root Path Cost – The cost of the path from this bridge to the Root Bridge.
– Topology Changes Counts – Specifies the total amount of STP state changes that have
occurred.
– Last Topology Change – Indicates the amount of time that has elapsed since the bridge
was initialized or reset, and the last topographic change that occurred. The time is
displayed in a day-hour-minute-second format, such as 2 days 5 hours 10 minutes and 4
seconds. The current root port and current root cost display as zero when this device is not
connected to the network.
– Interface – Indicates the port or LAG for which the STP information is displayed.
– STP Status – Indicates if STP is enabled on the port. The possible field values are:
– Enabled – Indicates that STP is enabled on the port.
– Disabled – Indicates that STP is disabled on the port.
– Fast Link – Indicates if Fast Link is enabled on the port. If Fast Link mode is enabled for
a port, the Port State is automatically placed in the Forwarding state when the port link is
up. Fast Link optimizes the STP protocol convergence. STP convergence can take 30-60
seconds in large networks. The possible field values are:
– Enable – Indicates that Fast Link is enabled on the port.
– Disable – Indicates that Fast Link is disabled on the port.
- FS728TP Smart Switch 1
- Software User Manual 1
- FCC Information to User 4
- FCC Declaration Of Conformity 5
- Contents 7
- About This Manual 11
- How to Use This Manual 12
- How to Print this Manual 12
- Chapter 1 14
- Switch Management Overview 14
- Chapter 2 16
- Getting Started 16
- Getting Started 2-2 17
- Figure 2-1 17
- Browser 18
- Network without DHCP server 19
- 2-5 Getting Started 20
- Figure 2-4 20
- Getting Started 2-6 21
- Figure 2-5 21
- Chapter 3 22
- Smartwizard Discovery Program 22
- Figure 3-1 23
- Chapter 5 25
- Figure 3-3 26
- Figure 3-4 27
- Setting, see 28
- Figure 3-2 28
- Figure 3-6 29
- Chapter 4 31
- Firmware Upgrade Procedure 31
- Figure 4-8 32
- Figure 4-9 33
- Figure 5-11 36
- Button Description 37
- Opens the Online Help 37
- Resetting the System 39
- Defining Device Information 40
- Viewing the Device Zoom View 41
- Figure 5-15 42
- Configuring System Time 43
- Figure 5-16 44
- . The Secondary SNTP 45
- Configuring Device Security 46
- Figure 5-17 47
- Defining Port Authentication 49
- 3. Edit the fields 51
- Viewing EAP Statistics 52
- Enabling Storm Control 54
- Figure 5-21 55
- Figure 5-22 56
- ACL Overview 57
- Figure 5-23 58
- Figure 5-24 60
- Figure 5-25 61
- Figure 5-26 62
- Port Based Security 63
- Figure 5-27 64
- 5. Modify the fields 66
- Configuring Passwords 67
- Defining RADIUS Settings 69
- Figure 5-31 72
- 2. Define the fields 73
- Viewing System Logs 74
- Logs Configuration 75
- Viewing the Memory Logs 77
- Viewing the Flash Logs 78
- Viewing Server Logs 79
- Figure 5-36 80
- Figure 5-37 82
- Figure 5-38 85
- Configuring Interfaces 88
- Figure 5-40 90
- Defining LAG Members 92
- Figure 5-41 93
- Figure 5-42 95
- Viewing LAG Membership 98
- Figure 5-44 99
- Configuring LACP 100
- Configuring VLANs 101
- Defining VLAN Properties 102
- Figure 5-47 103
- 6. Edit the VLAN Name 104
- Defining VLAN Membership 105
- Defining VLAN PVID Settings 107
- Defining IP Interfaces 108
- Configuring Static Addresses 111
- Figure 5-53 112
- Defining Dynamic Addresses 113
- Figure 5-55 115
- (BPDUs), the 117
- Figure 5-56 118
- Defining General QoS Settings 121
- Defining QoS Queues 123
- Figure 5-59 124
- Figure 5-60 126
- Mapping CoS to Queues 127
- Mapping DSCP Values to Queues 128
- Configuring SNMP Security 129
- Defining the Engine ID 130
- Defining SNMP Users 131
- Figure 5-65 132
- Defining SNMP Groups 134
- 3. Define the fields 136
- 3. Modify the fields 137
- Configuring SNMP Views 138
- Defining SNMP Communities 140
- Figure 5-72 142
- Figure 5-73 143
- Figure 5-74 144
- Figure 5-75 147
- Figure 5-76 148
- Defining Global Trap Settings 149
- Defining Trap Filter Settings 150
- Figure 5-79 151
- Configuring IGMP Snooping 153
- Figure 5-81 155
- Defining Multicast Groups 156
- Figure 5-83 158
- Figure 5-84 159
- – Forbidden – Forbidden 160
- Managing System Files 161
- Configuring File Uploads 162
- Configuring File Downloads 163
- Monitoring the Device 165
- Configuring Port Mirroring 166
- Figure 5-88 167
- 3. Modify the Type field 168
- Performing Copper Cable Tests 169
- Managing RMON Statistics 171
- Configuring RMON History 173
- Defining RMON History Control 173
- Figure 5-92 174
- Figure 5-93 175
- Figure 5-94 176
- Figure 5-95 177
- Defining RMON Events 179
- Figure 5-96 180
- Figure 5-97 181
- Figure 5-98 182
- Defining RMON Alarms 183
- Figure 5-100 185
- Figure 5-101 186
- Figure 5-102 187
- Appendix A 189
- Default Settings 189
Related products and manuals for Network switches Netgear FS728TP
Network switches Netgear GS108 User Manual
(140 pages)
(140 pages)
Network switches Netgear GS110TP User Manual
(32 pages)
(32 pages)
Network switches Netgear FS726TP User Manual
(16 pages)
(16 pages)
Network switches Netgear FSM726 User Manual
(25 pages)
(25 pages)
Network switches Netgear EN104TP User Manual
(14 pages)
(14 pages)
Network switches Netgear GS728TPP User Manual
(277 pages)
(277 pages)
Network switches Netgear GS108E User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 1.844 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals