Netgear WNAP210 User Manual Page 30
- Page / 126
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ProSafe Wireless-N Access Point WNAP210 Reference Manual
2-8 Installation and Configuration
v1.0 March 2009
• DHCP Client. By default, the Dynamic Host Configuration Protocol (DHCP) client is
disabled. If you have a DHCP server on your LAN and you enable DHCP, the wireless
access point will get its IP address, subnet mask, and default gateway settings
automatically from the DHCP server on your network when you connect the access point
to your LAN.
• IP Addr
ess. Enter the IP Address of your wireless access point.The default IP address is
192.168.0.236. To change it, enter an unused IP address from the address range used on
your LAN; or enable DHCP.
• IP Su
bnet Mask. The Access Point will automatically calculate the subnet mask based on
the IP address that you assign. Otherwise, you can use 255.255.255.0 (the default) as the
subnet mask.
• Default Gateway
. Enter the IP address of the gateway for your LAN. For more complex
networks, enter the address of the router for the network segment to which the wireless
access point is connected. The default is 0.0.0.0.
• Primary DNS Se
rvers. The access point will use this IP address as the primary Domain
Name Server used by stations on your LAN. The default is 0.0.0.0.
• Secondary DNS Se
rvers. The access point will use this IP address as the secondary
Domain Name Server used by stations on your LAN. The default is 0.0.0.0.
10. Click Ap
ply to save your Basic IP settings.
Note: If you change the default subnet of the LAN IP address, you will be
disconnected from the access point user interface. To reconnect, reconfigure
your computer with a static IP address within the new LAN IP subnet.
By default, the access point is set with the DHCP client
disabled. If your network uses dynamic IP
addresses, you must change this setting (see “Logging In to the Access Point” on page 2-14),
Configuring Your Wireless Settings
The following sections describe how to configure the wireless settings for 802.11b/g/n operation.
To configure the access point wireless settings:
1. Select Configuration > W
ireless.The Wireless Settings screen displays as shown in Figure 2-
6.
- ProSafe Wireless-N 1
- Access Point WNAP210 1
- Reference Manual 1
- FOR HOME OR OFFICE USE 5
- PY308400098 5
- Contents 7
- About This Manual 11
- How to Use This Manual 12
- How to Print This Manual 12
- Revision History 13
- Chapter 1 15
- Introduction 15
- Key Features and Standards 16
- Key Features 17
- 1-4 Introduction 18
- System Requirements 19
- What Is In the Box? 19
- Hardware Description 20
- Rear Panel 21
- 1-8 Introduction 22
- Chapter 2 23
- Figure 2-1 25
- Figure 2-2 27
- Figure 2-3 27
- Figure 2-4 28
- Figure 2-5 29
- Figure 2-6 31
- Deploying the Access Point 32
- Wall Mount Kit 34
- (Optional) 34
- Figure 2-8 36
- Setting Basic IP Options 37
- Wireless Settings 38
- Figure 2-10 39
- Configuring QoS Settings 42
- Figure 2-12 44
- Figure 2-13 50
- Setting Up a Security Profile 51
- Figure 2-15 52
- Figure 2-16 54
- Figure 2-17 56
- Figure 2-18 57
- Figure 2-19 58
- Figure 2-20 59
- Figure 2-21 60
- Figure 2-22 61
- Figure 2-23 63
- Chapter 3 65
- Management 65
- Remote Console 66
- Management Using Telnet 67
- 3-4 Management 68
- Management 3-5 69
- Figure 3-4 69
- Saving the Configuration 70
- Restoring the Configuration 70
- 1. Select Mainte 71
- 3-8 Management 72
- Enabling the Syslog Server 73
- Figure 3-9 74
- 3-10 Management 74
- Figure 3-10 75
- Management 3-11 75
- To access the System screen: 76
- 1. Select Monitoring > S 77
- Statistics screen 78
- Management 3-15 79
- Table 3-2. Statistics Fields 79
- Enabling Rogue AP Detection 80
- Figure 3-14 81
- Management 3-17 81
- Viewing and Saving AP Lists 82
- Figure 3-15 83
- Management 3-19 83
- Figure 3-16 83
- Creating AP Lists Manually 84
- Chapter 4 85
- Advanced Configuration 85
- 4-2 Advanced Configuration 86
- Figure 4-1 86
- Hotspot Settings 87
- 4-4 Advanced Configuration 88
- Figure 4-3 88
- Advanced Configuration 4-5 89
- 4-6 Advanced Configuration 90
- Figure 4-4 91
- Advanced Configuration 4-7 91
- 4-8 Advanced Configuration 92
- Advanced Configuration 4-9 93
- Figure 4-6 94
- Repeating screen displays 95
- Figure 4-7 96
- 4-12 Advanced Configuration 96
- Advanced Configuration 4-13 97
- Figure 4-8 97
- 4-14 Advanced Configuration 98
- Advanced Configuration 4-15 99
- Figure 4-9 99
- 4-16 Advanced Configuration 100
- Figure 4-10 100
- Advanced Configuration 4-17 101
- Figure 4-11 101
- 4-18 Advanced Configuration 102
- Troubleshooting and Debugging 103
- Chapter 5 103
- Default Settings 106
- Appendix A 107
- Technical Specifications 109
- Appendix B 111
- Related Documents 111
- B-2 Related Documents 112
- Appendix C 113
- Command Line Reference 113
- C-2 Command Line Reference 114
- Command Line Reference C-3 115
- C-4 Command Line Reference 116
- Command Line Reference C-5 117
- C-6 Command Line Reference 118
- Command Line Reference C-7 119
- C-8 Command Line Reference 120
- Numerics 121
Related products and manuals for WLAN access points Netgear WNAP210
WLAN access points Netgear WG102 User Manual
(70 pages)
(70 pages)
WLAN access points Netgear WNDAP350 User Manual
(136 pages)
(136 pages)
WLAN access points Netgear ME101 User Manual
(23 pages)
(23 pages)
WLAN access points Netgear WNAP320 User's Guide
(126 pages)
(126 pages)
WLAN access points Netgear WNDAP620 User Manual
(172 pages)
(172 pages)
WLAN access points Netgear WN604 User Manual
(70 pages)
(70 pages)
WLAN access points Netgear WAG102 User Manual
(102 pages)
(102 pages)
© 2020, manymanuals.com. All rights reserved. | 1.093 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals