Netgear WGE101 Installation Guide download pdf (Page 2)

If you have a Windows

computer, you can configure the bridge’s basic

connection settings using the NETGEAR Smart Navigator.

(With a Macintosh

, Linux

, or UNIX

computer, you use browser-

based configuration software to change the bridge’s settings. See the

WGE101 Reference Manual on the WGE101 54 Mbps Wireless Ethernet

Bridge Resource CD for details.)

To use the NETGEAR Smart Navigator:

1. Connect the bridge to a Windows computer.

2. Insert the WGE101 54 Mbps Wireless Ethernet Bridge Resouce CD

into the CD-ROM drive and follow the instructions to install the

NETGEAR Smart Navigator.

3. Choose Programs>NETGEAR

WGE101 Bridge>Smart

Navigator from the Start menu.

4. Select the bridge in the device list.

5. Click

Connection Settings.

6. To change the Country/Region,

select a different country or

region.

Note: Having the wrong

Country/Region setting may

violate local laws.

7. Make any other needed

connection settings changes.

8. To apply these changes, click OK, type admin as the User name and

password as the Password, click OK.

9. If the warning about selecting the incorrect region, appears, click Yes.

To make other changes (like changing the IP address or changing the

password), click the Advanced Settings button on the Smart Navigator

window. If you get a warning about the IP address not matching the

network IP address, see the Smart Navigator Reference Manual on the CD.

See the WGE101 Reference Manual on the CD for details about working

with the browser-based configuration sofware.

July 2003

WGE101 802.11g Wireless Ethernet Bridge Lights

PWR Green OFF: No power to the unit.

ON: Power applied to the unit.

WLAN Green OFF: No wireless LAN activity.

Flashing: Searching for an access point or

wireless router.

ON: Communicating to a wireless LAN.

LAN Green OFF: No Ethernet traffic.

Flashing: Wired Ethernet traffic.

ON: Connected to the Ethernet.

Reset to Factory Defaults

Press the Default button (located between the Ethernet port and the AC

adapter socket) for at least 6 seconds and then release the button. When

the lights stop flashing the bridge has been reset.

Quick Troubleshooting Tips

If you have trouble setting up your WGE101, check these tips. The trouble-

shooting section in the WGE101 Reference Manual on the WGE101 54 Mbps

Wireless Ethernet Bridge Resource CD has more details and additional tips.

The Wireless light is always blinking.

The bridge has not connected to a wireless network.

• Make sure the WGE101 is within range of the wireless network

• Make sure that the Network Name (SSID), WEP, and

Country/Region settings match those of the router or access point.

The Wireless light is on, but I cannot connect to the Internet.

There is a network configuration problem.

• Make sure the wireless network security (WEP) settings and the

bridge’s security (WEP) settings match.

• Make sure the IP addresses for the computer, bridge, and router all

start with the same numbers (for example, 192.168.0.yyy). Also, the

subnet masks should match (for example, 255.255.255.0).

• If a gaming console connected through a switch or hub cannot

connect to the Internet, with power on disconnect everything from

the switch or hub. Re-connect the bridge, then the game console(s).

Finally, connect any other device(s).

My bridge-enabled computer cannot communicate with my wireless-

enabled computer or printer.

There is a network configuration problem.

• Check that the wireless-enabled computer or printer is on the same

wireless network as the computer using the bridge.

• Make sure the WEP key (if WEP is enabled) and Country/Region

selection are the same for all devices using the same wireless network.

I cannot configure the WGE101 using a browser.

You did not specify the correct IP address for the bridge.

• Type the bridge’s IP address . The default address is 192.168.0.201.

• Make sure the IP addresses for your computer and the bridge have

the same IP subset address. The IP addresses for both devices should

start with the same numbers (for example, 192.168.0.yyy). Also, the

subnet masks should match (for example, 255.255.255.0).

Technical Support

PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED

WITH YOUR PRODUCT.

By registering your product at www.NETGEAR.com/register, we can provide

you with faster expert technical support and timely notices of product and

software upgrades.

NETGEAR, INC.

Support Information

Phone: 1-888-NETGEAR (for US & Canada only) — 24x7 phone support

For other countries see your Support information card.

E-mail: Support@NETGEAR.com (24x7 online support)

Web site: www.NETGEAR.com

Uplink and The Gear Guy are trademarks or registered trademarks of Netgear, Inc. in the

United States and/or other countries. Microsoft and Windows are trademarks or registered

trademarks of Microsoft Corporation in the United States and/or other countries. Other

brand or product names are trademarks or registered trademarks of their respective owners.

M-10131-02

Attention: When you configure the wireless settings of this device

please make sure to select the correct country settings. Due to EU-law,

the country settings must be identical to the country where the device

is operating (important due to non-harmonized frequencies in the EU).

0560

1 2

Comments to this Manuals

No comments

Netgear WGE101 Installation Guide Page 2

Comments to this Manuals

Related products and manuals for WLAN access points Netgear WGE101