Netgear XCM8903SF-10000S Datasheet download pdf (Page 5)

31. What is Single Rate Policing new feature?

Single Rate Policing feature enables support for Single Rate Policer as

deﬁned by RFC 2697:

• Committed Information Rate

- Average allowable rate for the class

• Committed Burst Size

- Maximum amount of contiguous packets for the class

• Excessive Burst Size

- Additional burst size for the class

- Credits reﬁll at a slower rate than committed burst size

• DiServ feature applied to class maps

32. What is Policy Based Routing new feature?

The Policy Based Routing feature overrides routing decision taken by

the router and makes the packet to follow dierent actions based on a

policy. It provides freedom over packet routing/forwarding instead of

leaving the control to standard routing protocols based on L3.

For instance, some organizations would like to dictate paths instead of

following the paths shown by routing protocols. Network Managers/

Administrators can set up policies such as:

• My network will not carry trac from the Engineering department

• Trac originating within my network with the following

characteristics will take path A, while other trac will take path B

• When load sharing needs to be done for the incoming trac across

multiple paths based on packet entities in the incoming trac

Conﬁguring PBR involves conﬁguring a route-map with match and set

commands and then applying the corresponding route-map to the

interface. IP routing must be enabled globally and on the interfaces

for PBR to operate. Policy Based Routing is applied to inbound trac

on interfaces.

37. What are the SFP/SFP+ optical transceivers supported by M6100 series?

NETGEAR GENUINE MODULES AND DAC CABLES:

MODEL TYPE DESCRIPTION

SFP PORTS SFP+ PORTS

AFM735 100BASE-FX NETGEAR SFP Multimode LC Transceiver Yes No

AGM731F 1000BASE-SX NETGEAR SFP Multimode LC Transceiver Yes Yes

AGM732F 1000BASE-LX NETGEAR SFP Single-mode LC Transceiver Yes Yes

AXM761 10GBASE-SR NETGEAR SFP+ Multimode LC Transceiver No Yes

AXM762 10GBASE-LR NETGEAR SFP+ Single-mode LC Transceiver No Yes

AXM763 10GBASE-LRM NETGEAR SFP+ Multimode LC Transceiver No Yes

AXM764 10GBASE-LR LITE NETGEAR SFP+ Single-mode LC Transceiver No Yes

AXC761 Direct-Attach NETGEAR 1M SFP+ to SFP+ DAC Cable No Yes

AXC763 Direct-Attach NETGEAR 3M SFP+ to SFP+ DAC Cable No Yes

Third party modules

ONLY THE FOLLOWING THIRD-PARTY MODULES ARE COMPATIBLE WITH M6100 CHASSIS SWITCH:

MODEL TYPE DESCRIPTION

SFP PORTS SFP+ PORTS

J9099B 100BASE-BX10-D HP® X112 100M SFP LC BX-D Transceiver Yes No

J9100B 100BASE-BX10-U HP® X112 100M SFP LC BX-U Transceiver Yes No

J4860C 1000BASE-LH HP® X121 1G SFP LC LH Transceiver Yes Yes

J9142B 1000BASE-BX10-D HP® X122 1G SFP LC BX-D Transceiver Yes Yes

J9143B 1000BASE-BX10-U HP® X122 1G SFP LC BX-U Transceiver Yes Yes

J9153A 10GBASE-ER HP® X132 10G SFP+ LC ER Transceiver Yes Yes

Third party Direct-Attach Cables

M6100 Chassis Switch supports third-party DAC passive and active cables, as long as they are SFP+ MSA compliant.

“HP” is registered trademark of Hewlett-Packard Company. Above list shows that NETGEAR successfully tested interoperability between these HP® transceivers and M6100 chassis switch on the

date of Oct, 1st 2014.

1 2 3 4 5 6

M6100 Chassis Switch 1

Comments to this Manuals

No comments

Netgear XCM8903SF-10000S Datasheet Page 5

Comments to this Manuals

Related products and manuals for Network switches Netgear XCM8903SF-10000S