Netgear GSM7226LP-100NES Datasheet download pdf (Page 12)

• The RPS4000 can be connected to a maximum of four switches (any combination

of M5300 series switches is supported) using RPS switch connectors and RPS

cables

• The RPS4000 provides protection against electrical issues such as high-voltage

(input, output) or short circuits for maximum security

• The RPS4000 can accommodate up to four hot-swap APS1000W power

modules

– Eitherone,two,threeorfourAPS1000Wpowermodulesarerequired,

depending on RPS or EPS application (see combinations in “Number of

APS1000W” table)

• In RPS mode with only one APS1000W power module, RPS4000 can protect up

to four (4) non-PoE or PoE M4100 series switches

– In case of a general switches power feed failure, powering all four switches

simultaneously for 12V DC system power

– RPS4000takesoveranddeliversadequatepowerwithoutanyservice

interruption (continuous monitoring)

– When the switch internal power is restored, the RPS4000 stops supplying

power to the switch automatically, again without any service interruption

• In RPS mode with multiple APS1000W power module combinations, RPS4000

can protect up to four (4) PoE M4100 series switches

– In case of a general switches power feed failure, powering all four switches

simultaneously (12V DC system power and -56V DC PoE)

– Same RPS functionality as with non-PoE switches including PoE power budget

protection

• In EPS mode with multiple APS1000W power module combinations, RPS4000

allows for various PoE 802.3af and 802.3at “full power” applications

– Supports M4100-50-POE, M4100-26G-POE; M4100-24G-POE+ and

M4100-50G-POE+

– Superseding switches main PSU for PoE budget and switch powering

– Delivering -56V DC for PoE power and 12V for switch power

– Switch main PSU system acts as built-in RPS for both switch power and PoE

budget protection

• In EPS mode, power slots can be organized into groups of two (Group 1 and Group

2) allowing for APS1000W power modules bridging

– Two APS1000W power modules can be bridged and deliver 1,440W PoE

budget to one 48-port switch M4100-50G-POE+

• Power slots can be conﬁgured for RPS or EPS mode

– All four power slots can be combined together with only one APS1000W

power module for four (4) 12V switches RPS application

– Power slots can be utilized in one-to-one mode for PoE switches RPS

applications

– Power slots can be bridged two by two for PoE switches EPS applications

The RPS4000 RPS/EPS unit supports the following key features:

•RPS mode: provide power backup for up to four switches concurrently

– With same level of protection as with four dedicated, “one-to-one” RPS units

•EPS mode: provide supplemental PoE power up to four switches concurrently

– Up to 2,880W shared PoE+ budget

– When in EPS mode, RPS4000 supersedes each switch main PSU

– Switch main PSU system power reverts to redundant power supply (RPS) function

RPS4000

RPS/EPS unit for up to 4 concurrent switches

Ordering information

•Americas, Europe: RPS4000-100NES

•Asia Paciﬁc: RPS4000-100AJS

•Warranty: 5 years

Front view

• RPS4000 is 1RU unit with four (4) empty slots

• Power modules (APS1000W) are sold separately

• APS1000WrequirementdependsonRPS,EPS,PoEapplication

Rear view

• Four (4) embedded RPS connectors

• Switch selectors for RPS/EPS power modes

• Switch selectors for power modules two-by-two bridging

Included:

• Four (4) RPS cables - 60cm each (~2 )

• Rack mount kit

• Power cord

ProSAFE® Intelligent Edge Managed Switches Data Sheet

M4100 series

Page12of36

Accessories

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 35 36

Comments to this Manuals

No comments

Netgear GSM7226LP-100NES Datasheet Page 12

Comments to this Manuals

Related products and manuals for Network switches Netgear GSM7226LP-100NES