Netgear WFS709TP User Manual Page 42
- Page / 222
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
WFS709TP ProSafe Smart Wireless Switch Software Administration Manual
2-6 Deploying a Basic WFS709TP System
v1.0, June 2007
2. (“Deployment Scenario #3” only) Configure a VLAN to connect the WFS709TP to your
network.
3. Connect the ports on the WFS709TP to your network.
4. (Optional) Configure a loopback address for the WFS709TP.
Run the Initial Setup
When you connect to theWFS709TP for the first time using either a serial console or a web
browser, the initial setup automatically launches. The initial setup requires you to set a master or
local role for the WFS709TP and passwords for administrator and configuration access. You must
also specify the country code for the country in which the WFS709TP will operate; this sets the
regulatory domain for the radio frequencies that the APs use.
The initial setup requires that you configure an IP address for the VLAN 1 interface, which you
can use to access and configure the WFS709TP remotely via a Secure Shell (SSH) or browser
interface session. Configuring an IP address for the VLAN 1 interface ensures that there is an IP
address and default gateway assigned to the WFS709TP upon completion of the initial setup.
Note: You do not need to perform this step if you are using VLAN 1 to connect the
WFS709TP to the wired network.
Note: You do not need to perform this step if you are using the VLAN 1 IP address as
the WFS709TP’s IP address.
Warning: Do not connect the WFS709TP Smart Wireless Switch to your network
before you run the initial setup for these reasons:
• The switch boots up with a default IP address which could interfere with
your network.
• The DHCP server on the switch is first enabled and then disabled after setup
is complete. If you connect the switch to your network before completing
the initial setup, the DHCP server is active on your network
- WFS709TP ProSafe 1
- Smart Wireless Switch 1
- Software Administration 1
- Lithium Battery Safety Notice 4
- European Union RoHS 5
- China RoHS 5
- Contents 7
- About This Manual 13
- How to Use This Manual 14
- How to Print this Manual 14
- Revision History 15
- Chapter 1 17
- Overview of the WFS709TP 17
- 1-2 Overview of the WFS709TP 18
- Figure 1-1 18
- Overview of the WFS709TP 1-3 19
- Figure 1-2 19
- 1-4 Overview of the WFS709TP 20
- Figure 1-3 20
- WFS709TP ProSafe Switches 21
- 1-6 Overview of the WFS709TP 22
- WFS709TP Software 23
- Basic WLAN Configuration 24
- Overview of the WFS709TP 1-9 25
- Encryption 26
- Overview of the WFS709TP 1-11 27
- 1-12 Overview of the WFS709TP 28
- Figure 1-5 28
- Association 29
- Overview of the WFS709TP 1-15 31
- 1-16 Overview of the WFS709TP 32
- Overview of the WFS709TP 1-17 33
- Figure 1-6 33
- Figure 1-7 33
- 1-18 Overview of the WFS709TP 34
- Overview of the WFS709TP 1-19 35
- 1-20 Overview of the WFS709TP 36
- Chapter 2 37
- Deployment Scenario #2 38
- Deployment Scenario #3 40
- Configuring the WFS709TP 41
- Run the Initial Setup 42
- Figure 2-4 43
- Figure 2-5 45
- Figure 2-6 45
- Figure 2-7 46
- ← arrow 47
- Figure 2-9 48
- Deploying APs 50
- Figure 2-12 52
- Figure 2-13 52
- Install APs 54
- Provision APs 54
- Figure 2-14 55
- Figure 2-15 55
- Additional Configuration 56
- Chapter 3 57
- Figure 3-1 58
- Figure 3-2 59
- Figure 3-3 59
- Configuring Static Routes 61
- Chapter 4 65
- Before You Begin 66
- Using RF Plan 67
- Building List Page 68
- Building Dimension Page 69
- 4-6 RF Plan 70
- Figure 4-3 70
- Figure 4-4 70
- AP Modeling Parameters Page 71
- 4-8 RF Plan 72
- AM Modeling Parameters Page 73
- Planning Floors Page 74
- RF Plan 4-11 75
- Figure 4-7 75
- 4-12 RF Plan 76
- Figure 4-8 76
- RF Plan 4-13 77
- Figure 4-9 77
- RF Plan 4-15 79
- Figure 4-13 79
- Figure 4-14 79
- 4-16 RF Plan 80
- AP Planning Page 81
- 4-18 RF Plan 82
- Figure 4-16 82
- AM Planning Page 83
- Exporting and Importing Files 84
- RF Plan 4-21 85
- Figure 4-21 85
- Figure 4-22 85
- RF Plan Example 86
- Create a Building 87
- Model the Access Points 88
- Model the Air Monitors 89
- Add and Edit a Floor 89
- Defining Areas 90
- RF Plan 4-27 91
- 4-28 RF Plan 92
- Figure 4-27 92
- Running the AP Plan 93
- Running the AM Plan 94
- 2. Click Save 95
- 4-32 RF Plan 96
- Chapter 5 97
- Configuring WLANS 97
- 5-2 Configuring WLANS 98
- Configuring WLANS 5-3 99
- Determine the Default VLAN 100
- Configuring WLANS 5-5 101
- Figure 5-1 101
- 5-6 Configuring WLANS 102
- Example Configuration 103
- 5-8 Configuring WLANS 104
- Configuring Global Parameters 105
- Add or Modify SSIDs 106
- Configuring WLANS 5-11 107
- Figure 5-3 107
- Configure AP Information 108
- Configuring WLANS 5-13 109
- Figure 5-4 109
- Configuring Radio Settings 110
- Configuring WLANS 5-15 111
- Figure 5-5 111
- 5-16 Configuring WLANS 112
- Add the location 4.2.6 114
- IntelliFi RF Management 115
- Configuring IRM 116
- Configuring WLANS 5-21 117
- 5-22 Configuring WLANS 118
- Chapter 6 119
- Configuring AAA Servers 119
- 6-2 Configuring AAA Servers 120
- Figure 6-1 120
- Configuring AAA Servers 6-3 121
- 6-4 Configuring AAA Servers 122
- Configuring AAA Servers 6-5 123
- 6-6 Configuring AAA Servers 124
- Chapter 7 125
- Figure 7-1 126
- Figure 7-2 127
- 802.1x Authentication Page 129
- Figure 7-4 131
- Chapter 8 133
- Configuring Captive Portal 134
- Figure 8-2 136
- Table 8-1 136
- Changing the Protocol to HTTP 137
- Figure 8-3 138
- Figure 8-4 139
- Figure 8-5 140
- Chapter 9 141
- Configuring Users 142
- Figure 9-2 143
- Chapter 10 145
- Adding Local WFS709TPs 145
- Configuring Local WFS709TPs 146
- Configuring Trusted Ports 147
- Configuring APs 147
- Rebooting APs 148
- Chapter 11 149
- Configuring Redundancy 149
- 11-2 Configuring Redundancy 150
- Figure 11-1 150
- Authentication 151
- Password 151
- Master WFS709TP Redundancy 152
- Configuring Redundancy 11-5 153
- Table 11-2. VRRP Associations 153
- 11-6 Configuring Redundancy 154
- Figure 11-2 154
- Configuring Redundancy 11-7 155
- 11-8 Configuring Redundancy 156
- Chapter 12 157
- Enabling AP Learning 158
- Classifying APs 158
- Figure 12-2 159
- Figure 12-3 160
- Misconfigured AP Detection 161
- Chapter 13 163
- Configuring SNMP 164
- SNMP for Access Points 166
- Figure 13-2 167
- Figure 13-3 169
- Figure 13-4 170
- Figure 13-5 170
- SNMP Traps 171
- Configuring Logging 174
- Figure 13-6 175
- Creating Guest Accounts 176
- Figure 13-11 178
- Managing Image Files 179
- Copying Log Files 180
- Copying Other Files 180
- Chapter 14 183
- Battery Boost 184
- WPA Fast Handover 186
- Appendix A 187
- Windows-Based DHCP Servers 188
- Configuring Option 43 189
- Linux DHCP Servers 190
- Appendix B 193
- Figure B-1 194
- Figure B-2 194
- Figure B-3 196
- Figure B-4 197
- Figure B-5 198
- Figure B-6 199
- Appendix C 201
- Internal Captive Portal 201
- Basic HTML Example 203
- Language Customization 206
- Internal Captive Portal C-11 211
- Figure C-1 211
- Customizing the Welcome Page 212
- Customizing the Pop-Up Box 214
- Appendix D 217
- Related Documents 217
- D-2 Related Documents 218
- Index-4 Index 222
Related products and manuals for Network switches Netgear WFS709TP
Network switches Netgear GS700TP User Manual
(188 pages)
(188 pages)
Network switches Netgear FS 524S User Manual
(60 pages)
(60 pages)
Network switches Netgear FS700TS User Manual
(42 pages)
(42 pages)
Network switches Netgear 7300S User Manual
(402 pages)
(402 pages)
Network switches Netgear FS728TP User Manual
(196 pages)
(196 pages)
Network switches Netgear GS108 User Manual
(140 pages)
(140 pages)
Network switches Netgear GS110TP User Manual
(32 pages)
(32 pages)
Network switches Netgear FS726TP User Manual
(16 pages)
(16 pages)
Network switches Netgear FSM726 User Manual
(25 pages)
(25 pages)
Network switches Netgear EN104TP User Manual
(14 pages)
(14 pages)
Network switches Netgear GS728TPP User Manual
(277 pages)
(277 pages)
Network switches Netgear GS108E User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 0.382 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals