Netgear ProSafe 10/100/1000 Switch W/SFP slots User Manual download pdf (Page 2)

start Here

The NETGEAR® ProSafe JGS524F 24 Port 10/100/1000 Mbps Switch with 2 SFP slots provides you with a low-cost, high-

performance network solution and are designed to support power workgroups operating at either 10 megabits per second (Mbps) or

With the ProSafe JGS524F 10/100/1000 Mbps Switch with optional SFP GBIC modules (AGM731F, AGM732F, AGM733),

improvement is accomplished very easily, with no change to the desktop (the network interface cards or software and the network

wiring).

As a result, the performance upgrade and the applications it enables are obtained very quickly and at a low cost.

Product Illustration

Front Panel of the ProSafe JGS524F Switch

10/100/1000 Mbps ports

Rear Panel of the ProSafe JGS524F Switch

^ЁЁЁшттЖ

JÛÛÛÛÛlÉjÛÛÛÛC

AC Power out

LEDs

The table below describes the activity of the LEDs.

Label Color Activity

Description

PWR (Power) Green On Power is suppiied to the Switch.

Off Power is disconnected.

Link / Activity Green

Soiid Vaiid Link on the port.

(Port Number)

Biinking Packet transmission or receiving on the port.

10/100/1OOOM

Orange

The port is operating in 1000 Mbps.

Green

Off

The port is operating in 10 Mbps mode, if corresponding L/A LED

is Soiid or Biinking

SFP

Green

Vaiid Link on the port

Biinking

Packet transmission or receiving on the port

SFP GBIC Module

The module bays accommodates standard SFP GBIC modules, such as the AGM73 IF or AGM732F fi'om NETGEAR, allowing you to

have fiber connections on your network. The module bays are combo ports, sharing a connection with an RJ-45 port. Being a combo port,

only one type of connection can be active at any given time. For example, both copper and fiber port cannot be used at the same time.

If both connectors are plugged in at the same time, the fiber port will be active.

The SFP GBIC bay accommodates a standard SFP GBIC module.

Installing an SFP GBIC Module

The following procedure describes how to install an SFP Gigabit Ethernet module in the switch's Gigabit module bay. Standard SFP

GBIC modules are sold separately from the JGS524F. If you do not want to install an SFP GBIC module at this time, skip this procedure.

To install an SFP GBIC module:

o Insert the SFP module into the SFP module bay. Press firmly to ensure the module seats into the connector.

Note: SFP transceivers are hot-swappable. The switch does not need to be powered off before installing or removig a transceiver.

However, always first disconnect the network eable before removing a transceiver.

Network Port -----------------

All ports on the switch are 10/100/1000 Mbps capable ports that auto negotiate for speed, and duplex. Additionally, all ports have Auto

Uplink™ to make the right connection.

Auto Uplink™

The Auto Uplink technology that NETGEAR has included in this product wUl automatically sense whether the straight-through cable

plugged into any port should have a 'normal' connection, e.g. connecting to a PC; or an 'uplink' connection, e.g. connecting to a router,

switch, or hub. That port will then configure itself to the correct configuration. This feature also eliminates the need to worry about

crossover cables, as Auto Uplink will accommodate either type of cable to make the right connection.

Note: Auto Uplink will compensate for setting uplink connections, and crossover or straight-through cables. Using Auto Uplink to create

multiple paths between any two network devices will disable your network.

Applications

Desktop Switching

ProSafe JGS524F switch is used as a desktop switch to build a small network that enables users to have 1000 Mbps access to a file

server. If a fiill-duplex adapter card is installed in the server or PC, a 2000Mbps connection is possible on the port where the server

or PC is completed.

Model JGS524F

100Mbps

10Mbps

Standards Compatibility

IEEE 802.3110BASE-T Ethernet, IEEE 802.3 100BASE-FX Fast Ethernet. IEEE 802.3x Flow Control,

IEEE 802.3ab lOOOBASE-TGigabit Ethernet, IEEE 802.3z 1000BASE-X

Compatible with major network software, including Windows, NetWare, and Linux

Date Rate 1000 Mbps with 4B/5B encoding and MLT-3 physical interface for 100BASE-TX

10,100 or 1000 Mbps half-duplex/20 200 or 2000 Mbps full-duplex

Network Interface

RJ-45 Maximum connector for 10BASE-T, 10OBASE-TX or 1000 BASE-T Ethernet interface

Power 28.5W

100-240VAC/50-60 Hz universal input

Dimensions 328x43.2x169mm

Weight 1.7kg/3.7 lbs

Environmental Specifications

Operating temperature: 0to40”C(32to104”F)

Operating humidity: 90% maximum relative humidity, noncondensing

Electromagnetic Compliance

VCCI Class А/ FCC Class А/ СЕ/ C-tick

Safety Agency Approvals

UL/CUL

Performance Specifications

Frame filter rate:1,480,000 for 1000Mbps

:148,000for100 Mbps

:14,800for10Mbps

Frame forward rate: 1,480,000 for 1000Mbps

:148,000for100 Mbps

:14,800for10Mbps

Network latency

(using 64-byte packets):100Mbpsto 100 Mbps: 10ps max

Address database size: 8000 MAC addresses

Queue buffer

256KB

M1 Uh

262491.8 hrs (29.9 yrs)

1 2

Comments to this Manuals

No comments

Netgear ProSafe 10/100/1000 Switch W/SFP slots User Manual Page 2

Comments to this Manuals