Netgear WAG102 User Manual Page 79
- Page / 102
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
ProSafe Dual Band Wireless Access Point WAG102 Reference Manual (802.11a/g)
Advanced Configuration 4-3
v2.0, September 2006
3. Enable the Wireless LAN Parameters by checking the Yes radio button and entering the
appropriate information in the fields described below:
• SuperA or SuperG Mode: Enable Super-A/G mode may increase the overall wireless
performance. The default is Disable.
• WMM Support: Wi-FI Multimedia (WMM) is disabled by default. Select the Enable
radio button to enable WMM support.
• RTS Threshold: Request to Send Threshold. The packet size that is used to determine if it
should use the CSMA/CD (Carrier Sense Multiple Access with Collision Detection)
mechanism or the CSMA/CA mechanism for packet transmission. With the CSMA/CD
transmission mechanism, the transmitting station sends out the actual packet as soon as it
has waited for the silence period. With the CSMA/CA transmission mechanism, the
transmitting station sends out an RTS packet to the receiving station, and waits for the
receiving station to send back a CTS (Clear to Send) packet before sending the actual
packet data. The default is 2346.
• Fragmentation Length: This is the maximum packet size used for fragmentation. Packets
larger than the size programmed in this field will be fragmented. The Fragment Threshold
value must be larger than the RTS Threshold value. The default is 2346.
• Beacon Interval: The Beacon Interval. Specifies the interval time between 20ms and
1000ms for each beacon transmission. The default is 100.
• DTIM Interval: The Delivery Traffic Indication Message. Specifies the data beacon rate
between 1 and 255. The default is 1.
4. Click Apply to enable the Advanced Wireless Settings.
Enabling Wireless Bridging and Repeating
The ProSafe 802.11a/g Dual Band Wireless Access Point WAG102 lets you build large bridged
wireless networks. Select the desired wireless access point mode for your environment:
• Wireless Point-to-Point Bridge. In this mode, the WAG102 will communicate ONLY with
another Bridge mode Wireless Station. You must enter the MAC address (physical address) of
the other Bridge mode Wireless Station in the field provided. WEP can (and should) be used to
protect this communication.
- NETGEAR ProSafe Dual 1
- Band Wireless Access 1
- Point WAG102 Reference 1
- Manual (802.11a/g) 1
- FOR HOME OR OFFICE USE 2
- FCC Statement 3
- European Community 5
- Contents 9
- 2.0, September 2006 12
- About This Manual 13
- How to Use This Manual 14
- How to Print this Manual 15
- Introduction 17
- Chapter 1 17
- Key Features and Standards 18
- Key Features 19
- 1-4 Introduction 20
- System Requirements 21
- What’s In the Box? 22
- Hardware Description 23
- Rear Panel 24
- 4. RJ-45 Ethernet Port 25
- 1-10 Introduction 26
- Chapter 2 27
- 0RO3AFE7IRELESS!CCESS0OINT 29
- Figure 2-2 31
- Figure 2-3 32
- Figure 2-4 33
- Figure 2-5 35
- Figure 2-6 35
- Figure 2-7 37
- Setting Basic IP Options 38
- Wireless Settings 40
- Figure 2-10 42
- Figure 2-11 45
- Figure 2-12 52
- Setting up a Security Profile 53
- Figure 2-14 54
- Figure 2-15 56
- Figure 2-16 57
- Figure 2-17 58
- Figure 2-18 59
- Figure 2-19 60
- Figure 2-20 61
- Figure 2-21 62
- Figure 2-22 64
- Chapter 3 65
- Management 65
- 3-2 Management 66
- Figure 3-2 66
- Management 3-3 67
- 3-4 Management 68
- Management 3-5 69
- Figure 3-3 69
- 3-6 Management 70
- Figure 3-4 70
- Management 3-7 71
- Table 3-1. Statistics Fields 71
- 3-8 Management 72
- Figure 3-5 72
- Management 3-9 73
- Figure 3-6 73
- Configuration File Management 74
- Management 3-11 75
- 3-12 Management 76
- Figure 3-8 76
- Chapter 4 77
- Advanced Configuration 77
- 4-2 Advanced Configuration 78
- Figure 4-2 78
- Advanced Configuration 4-3 79
- 4-4 Advanced Configuration 80
- Figure 4-3 80
- Advanced Configuration 4-5 81
- Figure 4-4 81
- 192.168.0.1 82
- Hub or Switch 82
- Advanced Configuration 4-7 83
- Segment 1 84
- Advanced Configuration 4-9 85
- 4-10 Advanced Configuration 86
- Chapter 5 87
- Troubleshooting 87
- The LAN light is not lit 88
- Troubleshooting 5-3 89
- 5-4 Troubleshooting 90
- Appendix A 91
- Technical Specifications 93
- Appendix B 95
- Related Documents 95
- B-2 Related Documents 96
- Numerics 97
Related products and manuals for WLAN access points Netgear WAG102
WLAN access points Netgear WGR614 v4 User Manual
(152 pages)
(152 pages)
WLAN access points Netgear MA101 User Manual
(67 pages)
(67 pages)
WLAN access points Netgear 802.11g User Manual
(108 pages)
(108 pages)
WLAN access points Netgear WG602v2 User's Guide
(122 pages)
(122 pages)
WLAN access points Netgear ME102 User Manual
(17 pages)
(17 pages)
WLAN access points Netgear WAG302v1 User Manual
(108 pages)
(108 pages)
© 2020, manymanuals.com. All rights reserved. | 0.620 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals