Netgear WAG102 User Manual Page 43
- Page / 102
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
ProSafe Dual Band Wireless Access Point WAG102 Reference Manual (802.11a/g)
Basic Installation and Configuration 2-17
v2.0, September 2006
It should not be necessary to change the wireless channel unless you experience
interference (shown by lost connections and/or slow data transfers). Should this happen,
you may need to experiment with different channels to see which is the best. See the
article on “Wireless Channels” available on the NETGEAR website. (A link to this article
and other articles of interest can be found in Appendix B, “Related Documents.”). By
default, the channel is set to Auto, where the wireless access point automatically selects
the most optimal channel for you. When selecting or changing channels, some points to
bear in mind:
– If using multiple access points, it is better if adjacent access points are manually set
use different channels to reduce interference. The recommended channel spacing
between adjacent access points is 5 channels (for example, use channels 1 and 6, or 6
and 11).
– In “Infrastructure” mode, wireless stations normally scan all channels, looking for an
access point. If more than one access point can be used, the one with the strongest
signal is used. This can only happen when the various access points are using the same
SSID.
• Data Rate. From the pull-down menu, select the available transmit data rate of the
wireless network. The possible data rates supported are: Best, 1 Mbps, 2 Mbps, 5.5 Mbps,
11 Mbps, 12 Mbps, 24 Mbps, 36 Mbps, 48 Mbps, and 54 Mbps. The default is Best.
• Output Power. From the pull-down menu, select the transmit power of the access point.
The options are Full, Half, Quarter, Eighth, and Min. Decrease the transmit power if two
or more APs are close together and use the same channel frequency. The default is Full.
(The transmit power may vary depending on the local regulatory regulations.
3. Click Apply to save your 802.11b/g wireless settings.
Setting Up and Testing Basic Wireless Connectivity
Follow the instructions below to set up and test basic wireless connectivity. Once you have
established basic wireless connectivity, you can enable security settings appropriate to your needs.
1. From your web browser, log in to the WAG102 as described in “Logging In Using the Default
IP Address” on page 2-11.
2. From the main menu under Setup, select Basic Settings. Verify that the correct Country/
Region in which the wireless interface will operate has been selected.
3. Click Apply to save any changes.
- NETGEAR ProSafe Dual 1
- Band Wireless Access 1
- Point WAG102 Reference 1
- Manual (802.11a/g) 1
- FOR HOME OR OFFICE USE 2
- FCC Statement 3
- European Community 5
- Contents 9
- 2.0, September 2006 12
- About This Manual 13
- How to Use This Manual 14
- How to Print this Manual 15
- Introduction 17
- Chapter 1 17
- Key Features and Standards 18
- Key Features 19
- 1-4 Introduction 20
- System Requirements 21
- What’s In the Box? 22
- Hardware Description 23
- Rear Panel 24
- 4. RJ-45 Ethernet Port 25
- 1-10 Introduction 26
- Chapter 2 27
- 0RO3AFE7IRELESS!CCESS0OINT 29
- Figure 2-2 31
- Figure 2-3 32
- Figure 2-4 33
- Figure 2-5 35
- Figure 2-6 35
- Figure 2-7 37
- Setting Basic IP Options 38
- Wireless Settings 40
- Figure 2-10 42
- Figure 2-11 45
- Figure 2-12 52
- Setting up a Security Profile 53
- Figure 2-14 54
- Figure 2-15 56
- Figure 2-16 57
- Figure 2-17 58
- Figure 2-18 59
- Figure 2-19 60
- Figure 2-20 61
- Figure 2-21 62
- Figure 2-22 64
- Chapter 3 65
- Management 65
- 3-2 Management 66
- Figure 3-2 66
- Management 3-3 67
- 3-4 Management 68
- Management 3-5 69
- Figure 3-3 69
- 3-6 Management 70
- Figure 3-4 70
- Management 3-7 71
- Table 3-1. Statistics Fields 71
- 3-8 Management 72
- Figure 3-5 72
- Management 3-9 73
- Figure 3-6 73
- Configuration File Management 74
- Management 3-11 75
- 3-12 Management 76
- Figure 3-8 76
- Chapter 4 77
- Advanced Configuration 77
- 4-2 Advanced Configuration 78
- Figure 4-2 78
- Advanced Configuration 4-3 79
- 4-4 Advanced Configuration 80
- Figure 4-3 80
- Advanced Configuration 4-5 81
- Figure 4-4 81
- 192.168.0.1 82
- Hub or Switch 82
- Advanced Configuration 4-7 83
- Segment 1 84
- Advanced Configuration 4-9 85
- 4-10 Advanced Configuration 86
- Chapter 5 87
- Troubleshooting 87
- The LAN light is not lit 88
- Troubleshooting 5-3 89
- 5-4 Troubleshooting 90
- Appendix A 91
- Technical Specifications 93
- Appendix B 95
- Related Documents 95
- B-2 Related Documents 96
- Numerics 97
Related products and manuals for WLAN access points Netgear WAG102
WLAN access points Netgear WGR614 v4 User Manual
(152 pages)
(152 pages)
WLAN access points Netgear MA101 User Manual
(67 pages)
(67 pages)
WLAN access points Netgear 802.11g User Manual
(108 pages)
(108 pages)
WLAN access points Netgear WG602v2 User's Guide
(122 pages)
(122 pages)
WLAN access points Netgear ME102 User Manual
(17 pages)
(17 pages)
WLAN access points Netgear WAG302v1 User Manual
(108 pages)
(108 pages)
© 2020, manymanuals.com. All rights reserved. | 1.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals