Netgear WND930 Installation Guide download pdf

Installation

NETGEAR Outdoor High Power Wireless N

Access Point

WND930

Set Up the Access Point

Before mounting the access point in a high location, ﬁrst set up and test the

unit to verify wireless network connectivity.

Note: The access point has a DHCP client enabled by default. If a DHCP server

exists in your network, the access point obtains an IP address from the DHCP

server. If a DHCP server is not detected in your network aer 30 seconds, the

access point sets its IP address to a static IP address of 192.168.0.100.

¾ To cable your access point:

1. Using an Ethernet cable, connect a power sourcing equipment (PSE) to

a PoE port on the access point.

Note: You must supply either AT power to at least one LAN port or AF power

to two LAN ports to power the access point. You must supply AT power to

both LAN ports to receive PoE power out.

2. If a DHCP server is not connected to your network, conﬁgure a

computer with a static IP address of 192.168.0.210 and a subnet mask

of 255.255.255.0.

3. Connect an Ethernet cable from a LAN port on the access point to a

LAN port on the PC.

4. Check the LEDs to verify that the access point is set up correctly.

Package Contents

Unpack the box and verify the contents:

• Outdoor High Power Wireless N Access Point

• Wall mounting bracket

• Four bracket screws

• Two grounding screws

• Two pole mount clamps

• Three weatherproof cable glands

LED Description

Power LED •O. Power is o.

•Solid green. Power is on.

•Amber, then blinking green. A self-test is running or soware is being

loaded. During startup, the LED is ﬁrst steady amber, then goes o, and

then blinks green before turning steady green aer about 45 seconds. If

aer one minute the LED remains amber or continues to blink green, it

indicates a system fault.

Activity LED •O. There is no network trac through the access point.

•Blinking green. There is network trac through the access point.

2.4G WLAN

LED

•O. The wireless interface is o.

•Solid green. The wireless interface is on.

•Blinking green. Wireless activity is detected on the 2.4G band.

5G WLAN LED •O. The wireless interface is o.

•Solid green. The wireless interface is on.

•Blinking green. Wireless activity is detected on the 5G band.

Heater LED •O. Heater is o.

•Solid green. Heater is on.

LAN port LEDs •O. No link is detected.

•Solid green. Link is detected.

•Solid amber. 10/100/1000 speed connection is detected.

•Blinking amber. 10/100/1000 speed activity is detected.

¾ To conﬁgure your access point for your network:

1. Connect to the access point by opening your browser and entering the

access point’s IP address

If a DHCP server is not installed in your network, the default IP address is

192.168.0.100.

A login window displays.

2. Enter admin for the user name and password for the password, both in

lower case letters.

The access point user interface displays.

3. Select Conﬁguration > System > Basic > General from the menu.

1 2

Summary of Contents

Page 1 - Installation

InstallationNETGEAR Outdoor High Power Wireless N Access PointWND930Set Up the Access PointBefore mounting the access point in a high location, ﬁrst s

Page 2 - Troubleshooting Tips

August 2014NETGEAR, Inc.350 East Plumeria DriveSan Jose, CA 95134, USANETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or reg

Netgear WND930 Installation Guide

Browse online or download Installation Guide for Routers Netgear WND930. Netgear WND930 Installation Guide User Manual

Summary of Contents

More documents for Routers Netgear WND930

Comments to this Manuals

Netgear WND930 Installation Guide

Browse online or download Installation Guide for Routers Netgear WND930. Netgear WND930 Installation Guide User Manual

Summary of Contents

More documents for Routers Netgear WND930

Comments to this Manuals

Related products and manuals for Routers Netgear WND930