Netgear GS524T User Manual

Browse online or download User Manual for Routers Netgear GS524T. Netgear GS524T User's Manual

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 1 - Copper Gigabit Switch

RCopper Gigabit SwitchInstallation Guide24 PORT10/100/1000 MbpsGS 524TMODEL

Page 2 - Statement of Conditions

introduction 1-2Package ContentsFigure 1-1 illustrates the Model GS524T switch package contents.Figure 1-1. Model GS524T Switch Package ContentsV

Page 3

physical description 2-1CHAPTER 2: PHYSICAL DESCRIPTIONThis chapter describes the hardware features of the NETGEAR Model GS524T CopperGigabit Swi

Page 4 - Internet/World Wide Web

physical description 2-2RJ-45 PortsThe Model GS524T switch has 24 auto-sensing 10/100/1000 Mbps UTP ports.Each port can operate at 1000 Mbps full-

Page 5 - CONTENTS

physical description 2-3Note: Using Auto Uplink to create multiple active paths between any two networkdevices can cause undesirable loops in the

Page 6 - APPENDIX C

physical description 2-4100-240 VAC 50-60 HzAC power ReceptacleFansLEDsTable 2-1 describes the activity of the LEDs.Table 2-1. LED DescriptionsLa

Page 7

applications 3-1CHAPTER 3: APPLICATIONSThis chapter presents an overview of the topologies possible by incorporating theNETGEAR Model GS524T Copp

Page 8

applications 3-2Segment Switching and Bridging from 10 Mbps or 100 Mbps to 1000 MbpsThe Model GS524T switch,as illustrated in Figure 3-2,connects

Page 9 - CHAPTER 1: INTRODUCTION

installation 4-1CHAPTER 4: INSTALLATIONThis chapter describes the installation procedures for the NETGEAR Model GS524TCopper Gigabit Switch.Prepa

Page 10 - Ethernet

installation 4-2• The Installation Guide• Support Information CardInstalling the Switch on a Flat SurfaceTo install the switch on a flat surface,

Page 11

installation 4-3Refer to Figure 4-2 when connecting the switch.Figure 4-2. Connecting to the Model GS524T SwitchVerifying InstallationWhen power

Page 12 - 2 = 100M Link LED

ii© 2002 by NETGEAR,Inc.All rights reserved.TrademarksNETGEAR®is a registered trademark of NETGEAR, Inc.in the United States and other Countries. Allo

Page 13

CHAPTER 5: TROUBLESHOOTINGThis chapter provides information about troubleshooting the NETGEAR ModelGS524T Copper Gigabit Switch.Table 5-1 lists sympto

Page 14 - Rear Panel

troubleshooting 5-2Network Adapter CardsMake sure the network adapter cards installed in the PCs are in working conditionand the software driver

Page 15 - CHAPTER 3: APPLICATIONS

technical specifications A-1APPENDIX A: TECHNICAL SPECIFICATIONSThis appendix provides technical specifications for the NETGEAR Model GS524TCoppe

Page 16 - 10/100Mbps

technical specifications A-2InterfaceRJ-45 Connectors for 10BASE-T Ethernet,100BASE-TX Fast Ethernet, and1000BASE-T Gigabit EthernetPower Consump

Page 17 - CHAPTER 4: INSTALLATION

technical specifications A-3Safety Agency ApprovalsUL Listed (UL 1950), cULTUV Licensed (EN 60 950)

Page 18

connector pin assignments B-1APPENDIX B: CONNECTOR PIN ASSIGNMENTSThis appendix provides information about the RJ-45 plug and the RJ-45 connector

Page 19 - 100 Mbps

connector pin assignments B-2Table B-1 lists the pin assignments for the 10/100/1000Mbps RJ-45 plug and the RJ-45 connector.Table B-1. 10/100/100

Page 20 - CHAPTER 5: TROUBLESHOOTING

cabling guidelines C-1APPENDIX C: CABLING GUIDELINESThis appendix provides specifications for cables used with the NETGEAR ModelGS524T Copper Gig

Page 21

cabling guidelines C-2Return LossReturn loss measures the amount of reflected signal energy resulting from impedancechanges in the cabling link.T

Page 22

cabling guidelines C-3Patch CablesWhen installing your equipment, replace old patch panel cables that do not meetCategory 5e specifications. As p

Page 23

iiiFederal Communications Commission (FCC) Compliance Notice:Radio Frequency NoticeThis device complies with part 15 of the FCC Rules. Operation is su

Page 24 - TUV Licensed (EN 60 950)

cabling guidelines C-4Category 5 CableCategory 5 distributed cable that meets ANSI/EIA/TIA-568-A building wiring standards can be a maximum of 32

Page 25 - 12345678

cabling guidelines C-5TxRx1236TxRx1236A BB B12361236TxRxTxRxTwisted Pair Cables for 100 BASE-TXFor two devices to communicate,the transmitter of

Page 26

cabling guidelines C-6Patch Panels and CablesIf you are using patch panels, make sure that they meet the 100BASE-TX require-ments.NETGEAR recomme

Page 27

cabling guidelines C-7

Page 28

RNETGEAR,Inc.4500 Great America ParkwaySanta Clara,CA 95054 USAPhone:1-888-NETGEARwww.NETGEAR.comM-GS524TNA-0

Page 29

ivCustomer SupportFor assistance with installing and configuring your NETGEAR system or with questions or problems following installation:• Check the

Page 30

contents vCONTENTSCHAPTER 1 IntroductionFeatures 1-1Package Contents 1-2CHAPTER 2 Physical DescriptionFront Panel 2-1RJ-45 2-2Auto-uplinkTM2-2L

Page 31

contents viAPPENDIX A Technical Specifications A-1APPENDIX B Connector Pin AssignmentsRJ-45 Plug and RJ-45 Connector B-1APPENDIX C Cabling Guidel

Page 32 - 87654321

contents viiFIGURESFigure 1-1. Model GS524T Switch Package Contents 1-2Figure 2-1. Front Panel of the Model GS524T Switch 2-1Figure 2-2. Rear Pa

Page 33

contents viiiTABLESTable 2-1. LED Descriptions 2-4Table 4-1. Operating Environment Requirements 4-1Table 5-1. Troubleshooting Information 5-1Tabl

Page 34 - Phone:1-888-NETGEAR

introduction 1-1CHAPTER 1: INTRODUCTION The NETGEAR Model GS524T 24-Port Copper Gigabit Switch provides you with alow-cost,high-performance netw

Comments to this Manuals

No comments