Netgear PS100 User Manual Page 133
- Page / 142
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
NetGear Print Server Manual
124
Appendix C CONFIG File
This appendix provides information for editing a CONFIG file. CONFIG files are stored in the flash
EEPROM of the NETGEAR PS100 series Print Sever and used for configuring the device using the
FTP method. For more information about using the CONFIG file and to see an example of FTP
commands, refer to the table of FTP Commands"on chapter 5 Unix. Only the parameters related to
TCP/IP operation of the print server are listed.
For modification of the various NetWare IPX/SPX and NetBEUI settings, NETGEAR recommends
that you use the included NETGEAR Print Server Administration Program or the PSCONFIG program.
CONFIG File TCP/IP Settings
When modifying the CONFIG file, use the configuration settings outlined below.
Configuration Settings
Parameter and
Command
Definition
Device Name
(0001 BOX_NAME)
The default name of the print server is PSxxxxxx (PS followed by 6 numbers). You can change
this, but the new name must not exceed 19 characters and must not include any spaces.
TCP/IP Protocol
(0012 TCPIP_P)
Enables or disables reception or transmission of TCP/IP packets.
IP Address
(4000 IP_ADDR)
This is the IP address for your print server. For more information about IP addressing, refer to
See
Understanding IP Addresses."
Device IP Address
(4001 GATEWAY)
If your network segment has a router, enter the router address here. If there is no router, leave the
address as 0.0.0.0.
Subnet Mask
(4002 MASK)
If the Gateway Address is 0.0.0.0, leave the Subnet Mask at 0.0.0.0. If you have a router, enter
the Subnet mask for the segment to which the print server is attached.
TCP Session Retry
Interval
(4010 TCP_INT)
Sets how long the print server should wait before retrying a TCP/IP connection that is lost.
Allowable values are from 0 to 255 seconds, with 2 as the default.
Retry Count
(4011 TCP_CNT)
Sets how many attempts for reconnection will be made. After attempting the set number, the
TCP/IP session is terminated. Allowable values are from 0 to 255, with 254 as the default.
L1 Logical Printer
Mapping
(0100 L1_PROUT)
The physical port that this L1 logical printer maps to.
String Before Job for L1
Logical Printer
(0101 L1_PREST)
The L1 logical printer control string (in hex) to be sent to the printer before each print job. Note: A
printer control string is limited to 15 characters.
Examples are:
ASCII = [Esc]&l0O
Hexadecimal = 1B266C304F
ASCII = [Esc]&l1O
Hexadecimal = 1B266C314F
String After Job
(0102 L1_POSTR)
The L1 logical printer control string (in hex) to be sent to the printer after each print job. Note: A
printer control string is limited to 15 characters.
Examples are:
ASCII = [Esc]&l0O
Hexadecimal = 1B266C304F
ASCII = [Esc]&l1O
Hexadecimal = 1B266C314F
Convert LF to CR+LF
(0103 L1_CHGLF)
If On, LF (line feed) characters are changed to CR+LF (carriage return + line feed). If off, no
conversion is done.
- Reference Manual 1
- Trademarks 2
- Statement of Conditions 2
- Customer Support 4
- Internet/World Wide Web 4
- Preface 5
- Conventions 6
- Related Publication 6
- TABLE OF CONTENT 7
- Chapter 1 Introduction 10
- LED Descriptions 11
- Rear Panel of PS111W 12
- Chapter 2 Installation 17
- 2-4 Verifying Power 19
- Server Status 22
- Configure Server 23
- TCP/IP Configuration Fields 25
- AppleTalk 26
- Wireless 27
- Network Type 28
- Wireless Link Info 30
- Printer Port 31
- Logical Printer 32
- NetWare General 34
- NetWare Print Server 34
- NetWare Remote Printer 36
- 4-1 Printing in Windows 38
- Figure 4-3 Components 41
- Figure 4-5 Program Folder 42
- Figure 4-6 43
- Figure 4-7 Complete Screen 44
- 4. Click on Next 48
- Auto-IP 50
- Wireless Configuration 52
- Figure 4-16 Add a Printer 54
- Figure 4-17 Set up printer 55
- ADD PORT Window 57
- Figure 4-20 Add Port message 57
- 3. Click on Next 59
- 5. Click on Next 61
- 6. Click on Next 62
- 7. Click on Next 62
- Server Using ARP” 66
- Configuration Example 73
- FTP Files in the Directory 75
- FTP Commands 75
- Configuring LPD on System V 77
- Configuring LPD on BSD 78
- Printing Using LPD 79
- Printing Using FTP 79
- Printing Using DSI 79
- 6-3 Using PSTool Utility 82
- 7-1 Configuration Overview 84
- PSERVER mode: 94
- NetWare NDS Remote Printer 98
- NetGear Print Server Manual 100
- Using Logical Ports 104
- Program 105
- Buttons 106
- Browse Button 107
- Exit Button 107
- System Tab 108
- System Tab Fields 109
- TCP/IP Tab 110
- NetWare PServer Menu Tab 111
- NetWare RPrinter Menu Tab 112
- AppleTalk Tab 113
- AppleTalk Tab Fields 114
- Logical Port Tab 115
- Physical Port Tab 116
- Wireless Tab 117
- same Channel number 119
- Link Info Screen 120
- 8-3 Menu Options 121
- Printer Menu 122
- Configuring Using IP Setup 123
- Three Main Address Classes 128
- Netmask 129
- Subnet Addressing 130
- Private IP Addresses 131
- Address Resolution Protocol 132
- IP Configuration by DHCP 132
- Appendix C CONFIG File 133
- CONFIG File Line Numbers 134
- Overview 135
- Create Printer Agent 136
- Create Printer Agent Window 136
- Workstation Configuration 137
- Appendix E IP Setup 139
Related products and manuals for Print servers Netgear PS100
Print servers Netgear PS111W User Manual
(106 pages)
(106 pages)
Print servers Netgear PS121v2 User Manual
(50 pages)
(50 pages)
© 2020, manymanuals.com. All rights reserved. | 0.513 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals