Netgear XM128 ISDN User Manual Page 56
- Page / 156
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Reference Guide for the Model XM128 ISDN Digital Modem
6-8 ISDN Overview
If you want the Model XM128 modem to answer inbound calls using all possible protocols, refer
to Table 6-4 for the commands used to set the best-effort call answering bit.
Ambiguity Resolution Switch for Voice Calls
For a speech or voice-band-data call, if the &ZI number assignment can tell which of the analog
adapters is being addressed, then the call is delivered to the proper destination. Sometimes,
however, ambiguity of address matching may exist. This ambiguity may exist if the &ZIn numbers
of the various protocols are either unassigned or not matched or the address information is absent
in the incoming setup message. In this case, users may want to set answering priority to an analog
port. The AT&Ln command sets the address ambiguity resolution flag as follows:
• AT&L0
The analog adapter 1 has the higher priority to answer a voice or voice-band-analog-data call.
If the analog adapter 1 is busy, the call is routed to the analog adapter, PHONE 2.
• AT&L1
The analog adapter 2 has the higher priority to answer a voice or voice-band-analog-data call.
If the analog adapter 2 is busy, the call is routed to the analog adapter, PHONE 1.
Multi Auto-Answering of Data Calls
When an ISDN data call comes in, the Model XM128 modem can determine the protocol to be
used in one of two ways.
One is way is through the information conveyed by the setup message. For DSS1, this information
includes the bearer capability, low-layer compatibility, or high-layer compatibility information
elements; for 1TR6, it includes the Service Indicator as well as an Additional Octet of the Service
Indicator.
The other way is by the Multi Auto-answering process. The Model XM128 modem determines
the protocol by monitoring the B channel signal sent by the calling site.
With either method, the data call can be identified by the modem to be X.75, V.110, V.120,
or PPP, MPPP Async-to-Sync conversion.
Table 6-4. Best-effort call answering bit commands
Command Function
ATS119.3=0 Answer call only when number matched (by default)
ATS119.3=1 Best-effort call answering
- Reference Guide for the 1
- Model XM128 ISDN 1
- Digital Modem 1
- Trademarks 2
- Statement of Conditions 2
- VCCI-2 Statement 3
- Customer Support 3
- World Wide Web 4
- Bulletin Board Service 4
- Contents 5
- Preface xvii 17
- Conventions 18
- Related Publication 19
- Table 2. Manuals 20
- Chapter 1 21
- Introduction 21
- 1-2 Introduction 22
- Front Panel 23
- 1-4 Introduction 24
- Table 1-2. LED descriptions 24
- Introduction 1-5 25
- Rear Panel 26
- Introduction 1-7 27
- Chapter 2 29
- Installation 29
- Installing the Modem 30
- Chapter 3 33
- NETGEAR XM128, PPP 64K 34
- NETGEAR XM128 V.120 64K 34
- Chapter 4 35
- Configuration 35
- Understanding AT Commands 36
- Configuration 4-3 37
- Communication Speed Setup 38
- Configuration 4-5 39
- 4-6 Configuration 40
- Entering DNs 41
- 4-8 Configuration 42
- Chapter 5 43
- Async to Sync PPP 43
- 5-2 Async to Sync PPP 44
- Multilink PPP 45
- 5-4 Async to Sync PPP 46
- Async to Sync PPP 5-5 47
- Chapter 6 49
- ISDN Overview 49
- 6-2 ISDN Overview 50
- Placing the Call 51
- Commands for Incoming Calls 52
- Determining the Packet Length 53
- Answering a Call Using MSN 54
- ISDN Overview 6-7 55
- 6-8 ISDN Overview 56
- ISDN Overview 6-9 57
- V.110 ISDN Communications 58
- V.120 ISDN Communications 59
- Configuring the V.120 Mode 60
- Dialing in V.120 Mode 61
- 6-14 ISDN Overview 62
- 128 Kbps Speeds 63
- 6-16 ISDN Overview 64
- ISDN Overview 6-17 65
- 6-18 ISDN Overview 66
- ISDN Overview 6-19 67
- Chapter 7 69
- Advanced ISDN 69
- 7-2 Advanced ISDN 70
- Advanced ISDN 7-3 71
- 7-4 Advanced ISDN 72
- Advanced ISDN 7-5 73
- 7-6 Advanced ISDN 74
- Answering a Call 75
- Answering a Call for 1TR6 76
- Best-effort Call Answering 76
- Advanced ISDN 7-9 77
- 7-10 Advanced ISDN 78
- Placing a Call 79
- Placing a Call for 1TR6 80
- User-To-User Information 81
- Chapter 8 83
- Analog Call Handling 83
- AT Commands for Analog Calls 84
- Analog Call Handling 8-3 85
- Accepting an Incoming Call 86
- Chapter 9 87
- Modem Upgrade 87
- Upgrade Instructions 88
- Kernel Mode 88
- Chapter 10 89
- Troubleshooting 89
- Loopback Tests 90
- The Diagnostic Command 91
- Modem Reset 92
- Troubleshooting 10-5 93
- 10-6 Troubleshooting 94
- Table 10-2. EPA Commands 94
- Troubleshooting 10-7 95
- Appendix A 97
- Technical Specifications 97
- Appendix B 99
- Security Functions 99
- Level 1 Security 100
- Level 2 Security 100
- Level 3 Security 101
- B-4 Security Functions 102
- Appendix C 103
- AT Command Set Reference 103
- AT Command Descriptions 104
- AT Command Set Reference C-3 105
- C-4 AT Command Set Reference 106
- AT Command Set Reference C-5 107
- C-6 AT Command Set Reference 108
- Description of ATI3 Output 109
- Table C-3 110
- AT Command Set Reference C-9 111
- C-10 AT Command Set Reference 112
- AT Command Set Reference C-11 113
- C-12 AT Command Set Reference 114
- Appendix D 115
- Setting S-Registers 116
- S-Register Descriptions 118
- ATXn Result Code Option Table 133
- Table D-6. Result code chart 135
- Table D-8 137
- lists the connect strings 137
- Appendix E 139
- Connector Pin Assignments 139
- Table E-2 140
- RJ-11 Plug and Connector 141
- Appendix F 143
- Serial Port Interface 143
- F-2 Serial Port Interface 144
- Appendix G 145
- ISDN Reference 145
- Basic Rate Interface 146
- Out-of-Band Signaling 146
- ISDN Reference G-3 147
- Ordering ISDN Service 148
- ISDN Reference G-5 149
- G-6 ISDN Reference 150
- ISDN Reference G-7 151
- G-8 ISDN Reference 152
- Numerics 153
Related products and manuals for ISDN access devices Netgear XM128 ISDN
(42 pages)
© 2020, manymanuals.com. All rights reserved. | 1.370 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals