Netgear XM128 ISDN User Manual Page 35
- Page / 156
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Configuration 4-1
Chapter 4
Configuration
This chapter describes the procedures for configuring your Model XM128 modem and your ISDN
line.
Configuring Your ISDN Line and Network
The setup procedure for the Model XM128 modem needs to be done only once. The settings are
stored in the nonvolatile random access memory (NVRAM) of the modem. Turning power on and
off will not erase the information. The only time that you need to reconfigure your line is when you
perform a hardware reset on your modem when you change options on your ISDN line.
NETGEAR provides a simple Windows 95 or NT 4.0 utility to help you set up the Model XM128
modem. Refer to
Getting Started Using FirstGear for the XM128 ISDN Digital Modem
for
complete instructions. This chapter explains how to set up your switch using the Windows/
Windows 95 utility that comes with the modem.
If your Model XM128 modem is not going to be set up by a computer running Windows, use
a terminal program that allows you to send AT commands to the modem and receive responses
from it.
Configuring Your Modem Using a Terminal Program
If you are not running Windows 95 or Windows NT, configure your Model XM128 modem with
a terminal program that allows you to send and receive AT commands and responses from the
modem.
NETGEAR recommends that you have your Model XM128 modem ready to use before the
telephone company installs your ISDN line. If the modem is ready, you can enter the SPID and
confirm that the ISDN network is responding properly before the telephone installer leaves.
- Reference Guide for the 1
- Model XM128 ISDN 1
- Digital Modem 1
- Trademarks 2
- Statement of Conditions 2
- VCCI-2 Statement 3
- Customer Support 3
- World Wide Web 4
- Bulletin Board Service 4
- Contents 5
- Preface xvii 17
- Conventions 18
- Related Publication 19
- Table 2. Manuals 20
- Chapter 1 21
- Introduction 21
- 1-2 Introduction 22
- Front Panel 23
- 1-4 Introduction 24
- Table 1-2. LED descriptions 24
- Introduction 1-5 25
- Rear Panel 26
- Introduction 1-7 27
- Chapter 2 29
- Installation 29
- Installing the Modem 30
- Chapter 3 33
- NETGEAR XM128, PPP 64K 34
- NETGEAR XM128 V.120 64K 34
- Chapter 4 35
- Configuration 35
- Understanding AT Commands 36
- Configuration 4-3 37
- Communication Speed Setup 38
- Configuration 4-5 39
- 4-6 Configuration 40
- Entering DNs 41
- 4-8 Configuration 42
- Chapter 5 43
- Async to Sync PPP 43
- 5-2 Async to Sync PPP 44
- Multilink PPP 45
- 5-4 Async to Sync PPP 46
- Async to Sync PPP 5-5 47
- Chapter 6 49
- ISDN Overview 49
- 6-2 ISDN Overview 50
- Placing the Call 51
- Commands for Incoming Calls 52
- Determining the Packet Length 53
- Answering a Call Using MSN 54
- ISDN Overview 6-7 55
- 6-8 ISDN Overview 56
- ISDN Overview 6-9 57
- V.110 ISDN Communications 58
- V.120 ISDN Communications 59
- Configuring the V.120 Mode 60
- Dialing in V.120 Mode 61
- 6-14 ISDN Overview 62
- 128 Kbps Speeds 63
- 6-16 ISDN Overview 64
- ISDN Overview 6-17 65
- 6-18 ISDN Overview 66
- ISDN Overview 6-19 67
- Chapter 7 69
- Advanced ISDN 69
- 7-2 Advanced ISDN 70
- Advanced ISDN 7-3 71
- 7-4 Advanced ISDN 72
- Advanced ISDN 7-5 73
- 7-6 Advanced ISDN 74
- Answering a Call 75
- Answering a Call for 1TR6 76
- Best-effort Call Answering 76
- Advanced ISDN 7-9 77
- 7-10 Advanced ISDN 78
- Placing a Call 79
- Placing a Call for 1TR6 80
- User-To-User Information 81
- Chapter 8 83
- Analog Call Handling 83
- AT Commands for Analog Calls 84
- Analog Call Handling 8-3 85
- Accepting an Incoming Call 86
- Chapter 9 87
- Modem Upgrade 87
- Upgrade Instructions 88
- Kernel Mode 88
- Chapter 10 89
- Troubleshooting 89
- Loopback Tests 90
- The Diagnostic Command 91
- Modem Reset 92
- Troubleshooting 10-5 93
- 10-6 Troubleshooting 94
- Table 10-2. EPA Commands 94
- Troubleshooting 10-7 95
- Appendix A 97
- Technical Specifications 97
- Appendix B 99
- Security Functions 99
- Level 1 Security 100
- Level 2 Security 100
- Level 3 Security 101
- B-4 Security Functions 102
- Appendix C 103
- AT Command Set Reference 103
- AT Command Descriptions 104
- AT Command Set Reference C-3 105
- C-4 AT Command Set Reference 106
- AT Command Set Reference C-5 107
- C-6 AT Command Set Reference 108
- Description of ATI3 Output 109
- Table C-3 110
- AT Command Set Reference C-9 111
- C-10 AT Command Set Reference 112
- AT Command Set Reference C-11 113
- C-12 AT Command Set Reference 114
- Appendix D 115
- Setting S-Registers 116
- S-Register Descriptions 118
- ATXn Result Code Option Table 133
- Table D-6. Result code chart 135
- Table D-8 137
- lists the connect strings 137
- Appendix E 139
- Connector Pin Assignments 139
- Table E-2 140
- RJ-11 Plug and Connector 141
- Appendix F 143
- Serial Port Interface 143
- F-2 Serial Port Interface 144
- Appendix G 145
- ISDN Reference 145
- Basic Rate Interface 146
- Out-of-Band Signaling 146
- ISDN Reference G-3 147
- Ordering ISDN Service 148
- ISDN Reference G-5 149
- G-6 ISDN Reference 150
- ISDN Reference G-7 151
- G-8 ISDN Reference 152
- Numerics 153
Related products and manuals for ISDN access devices Netgear XM128 ISDN
(42 pages)
© 2020, manymanuals.com. All rights reserved. | 0.500 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals