Netgear 771S User Manual download pdf (Page 55)

Index—AT Commands

Rev. 1 Sep.13 Proprietary and Confidential 55

+ICF, set TE-TA control character framing, 38

!IDSTEST, start DM session, 36

+IFC, set TE-TA local data flow control, 38

+ILRR, set TE-TA local rate reporting mode, 38

+IPR, set fixed local rate, 38

L, set monitor speaker loudness, 38

M, set monitor speaker mode, 38

$MDN, Set/return Mobile Directory Number, 19

$MIPERR, Return last MIP error code, 24

$MSID, Set/return MSID, 20

O, switch from command mode to data mode, 38

P, select pulse dialing, 38

!PACKAGE, return package version string, 20

!PCTEMP, return current temperature information, 21

$PRL, Return CDMA PRL version, 21

Q, set result code presentation mode, 38

$QCMIP, Set/return Mobile IP state, 24

$QCMIPEP, Enable/disable active profile, 24

$QCMIPGETP, Return information about specified profile, 25

$QCMIPHA, Set/return active profile’s home IP address, 25

$QCMIPMASPI, Set/return active profile’s MN-AAA SPI, 26

$QCMIPMASS, Set/return active profile’s MN-AAA shared

secret (ASCII), 26

$QCMIPMASSX, Set/return active profile’s MN-AAA shared

secret (Hex), 27

$QCMIPMHSPI, Set/return active profile’s HA SPI, 27

$QCMIPMHSS, Set/return active profile’s MN-HA shared se-

cret (ASCII), 28

$QCMIPMHSSX, Set/return active profile’s MN-HA shared

secret (Hex), 28

$QCMIPNAI, Set/return active profile’s NAI, 29

$QCMIPP, Set/return active profile, 29

$QCMIPPHA, Set/return active profile’s primary home agent

IP address, 30

$QCMIPRT, Enable/disable reverse tunneling, 31

$QCMIPSHA, Set/return active profile’s secondary home

agent IP address, 30

$QCMIPT, Return RFC 2002bis authentication state, 31

$QRMCALL, make/disconnect data connection, 21

!RESET, reset the modem, 22

$RESET, Reset (power cycle) the device, 22

$ROAM, Set/return roaming mode, 22

$RT, Reset device to factory defaults, 22

&S, set DSR signal, 37

S0, set number of rings before auto-answer, 39

S10, set disconnect delay after indicating absence of data car-

rier, 39

S3, set command line termination character, 39

S4, set response formatting character, 39

S5, set command line editing character, 39

S6, set pause before blind dialing, 39

S7, set number of seconds to wait for connection completion,

S8, set number of seconds to wait when comma dial modifier

used, 39

!SETCND, set AT command password, 14

&T, auto tests, 37

T, select tone dialing, 39

&V, return AT configuration parameters, 37

V, set result code format mode, 39

+VTD, tone duration, 45

+VTS, DTMF and arbitrary tone generation, 45

&W, Store parameter to user-defined profile, 37

+WS46, PCCA STD 101 select wireless network, 45

X, set connect result code format and call monitoring, 39

Z, set all current parameters to user-defined profile, 39

1 2 ... 50 51 52 53 54 55 56 57 58 59 60

Comments to this Manuals

No comments

Netgear 771S User Manual Page 55

Comments to this Manuals