350 East Plumeria DriveSan Jose, CA 95134USADecember 2012202-11024-03ReadyDATA 5200Hardware Manual
Getting Started10NETGEAR ReadyDATA 5200 7. Press and release the Reset button to scroll through the boot menu options.Watch the blink pattern of the p
Getting Started11 NETGEAR ReadyDATA 5200Factory SettingsThe following table lists factory settings for the ReadyDATA 5200.Table 2. Factory settings F
Getting Started12NETGEAR ReadyDATA 5200 Technical SpecificationsThe following table lists the technical specifications for the ReadyDATA 5200. Table 3
1322. Expansion Disk ArraysThis chapter describes physical features of the EDA2000 and EDA4000, which are optional expansion disk arrays you can use
Expansion Disk Arrays14NETGEAR ReadyDATA 5200 Front PanelThe following figure shows the front panel of the EDA2000 (2U expansion disk array), top, and
Expansion Disk Arrays15 NETGEAR ReadyDATA 5200The following figure shows the control panels in more detail. 1234567812367485Figure 7. EDA2000 and EDA4
Expansion Disk Arrays16NETGEAR ReadyDATA 5200 For more information about adding and replacing disk drives, see Add a Disk on page 23 and Replace a Dis
Expansion Disk Arrays17 NETGEAR ReadyDATA 5200Status InformationThe status indicators on the EDA2000 and EDA4000 are the same as on the ReadyDATA 5200
Expansion Disk Arrays18NETGEAR ReadyDATA 5200 The following table lists the technical specifications for the EDA4000.Table 5. EDA4000 technical speci
1933. MaintenanceThis chapter describes how to perform maintenance activities like adding disks and replacing disks and system components. It includ
2NETGEAR ReadyDATA 5200 SupportThank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your p
Maintenance20NETGEAR ReadyDATA 5200 Front BezelThe ReadyDATA 5200, EDA2000, and EDA4000 come with a front bezel that protects the drive bays with a lo
Maintenance21 NETGEAR ReadyDATA 5200 To remove the front bezel:1. If the bezel is locked, unlock it.2. Push the release latch on the left side of the
Maintenance22NETGEAR ReadyDATA 5200 DisksThe ReadyDATA 5200 does not recognize non-NETGEAR disks. In addition, if you use non-NETGEAR disks, Dashboard
Maintenance23 NETGEAR ReadyDATA 5200Add a DiskYou can add a hard disk to an empty disk bay. You do not need to shut down your unit before adding a dis
Maintenance24NETGEAR ReadyDATA 5200 3. Turn the disk over and remove the metal plate from the drive tray.4. (Optional) Depending on the thickness of t
Maintenance25 NETGEAR ReadyDATA 52006. Align the screw holes on the disk drive with the screw holes on the metal tabs and install the screws to fasten
Maintenance26NETGEAR ReadyDATA 5200 To add a 3.5-inch disk:1. Pull the disk tray release switch. The tray handle pops out. 12 1. Disk tray handle2.
Maintenance27 NETGEAR ReadyDATA 5200Replace a DiskIf a disk fails, your system provides email alerts and status messages about the need to replace a d
Maintenance28NETGEAR ReadyDATA 5200 4. Remove the screws that hold the disk drive to the metal tabs and remove the old disk drive.5. Replace the disk
Maintenance29 NETGEAR ReadyDATA 5200 To replace a 3.5-inch disk:1. If a disk failed, scan disk LEDs on the disk bays to identify the failed disk.2. P
3Table of ContentsChapter 1 Getting StartedFront Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance30NETGEAR ReadyDATA 5200 System ComponentsYou can replace system components on your ReadyDATA 5200, EDA2000, or EDA4000.Power SupplyIf eith
Maintenance31 NETGEAR ReadyDATA 5200WARNING:Ensure that the chassis cover is in place when the system is operating to allow proper cooling. Out-of-war
Maintenance32NETGEAR ReadyDATA 5200 BatteryYour system uses a CR2032 battery. Dispose of used batteries according to the manufacturer’s instructions.D
33AA. Warnings and PrecautionsThis appendix contains safety warnings and precautions for the ReadyDATA 5200 . It includes the following sections:• S
Warnings and Precautions34NETGEAR ReadyDATA 5200Safety Warnings1. The equipment is certified for installation only by trained personnel, according to
Warnings and Precautions35NETGEAR ReadyDATA 5200• Do not use mats designed to decrease static electrical discharge as protection from electrical shock
Warnings and Precautions36NETGEAR ReadyDATA 5200Electrostatic Discharge (ESD) PrecautionsElectrostatic discharge is generated by two objects with diff
37BB. Notification of ComplianceRegulatory Compliance InformationThis section includes user requirements for operating this product in accordance wi
Notification of Compliance38NETGEAR ReadyDATA 5200FCC Declaration Of ConformityWe, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare
411. Getting StartedCongratulations on your purchase of a NETGEAR® ReadyDATATM 5200. This ReadyDATA 5200 Hardware Manual describes the physical feat
Getting Started5 NETGEAR ReadyDATA 5200Front PanelThe following figure shows the front panel of the ReadyDATA 5200 with the optional front bezel remov
Getting Started6NETGEAR ReadyDATA 5200 Each drive bay features a latch that releases the pop-out tray handle, as shown in the following figure.12Figur
Getting Started7 NETGEAR ReadyDATA 5200Rear PanelThe following figure shows the rear panel of the ReadyDATA 5200. 123 456789Figure 5. ReadyDATA 5200 r
Getting Started8NETGEAR ReadyDATA 5200 You can shut down your unit in these ways:• Using the Power button:• Preferred shutdown. Press the Power button
Getting Started9 NETGEAR ReadyDATA 5200Boot MenuUse the boot menu to restart or troubleshoot your ReadyDATA 5200. It has the following boot modes:• No
Comments to this Manuals