Netgear FA411 Installation Guide

Browse online or download Installation Guide for Camera accessories Netgear FA411. Netgear FA411 Installation Guide User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Connect the Network Cables
Using a UTP cable, connect any port on a hub or switch to the port on the network card.
Note: One of the ports on NETGEAR hubs is switchable between Normal (MDI-X) and Uplink
(MDI) with a Normal/Uplink push button. If you are using this switchable port on a NETGEAR hub
to connect to a PC or the network card, make sure the Normal/Uplink push button is set
to Normal.
Install the Network Driver
This section explains how to install the Windows 98 Network Driver. Some versions of Windows 98 may
respond with different dialog boxes,or the dialog boxes may open in a different sequence than those
shown in this guide,but should prompt you for the same information.
Note: You must install the network card before installing the network driver.
Before you proceed with the installation steps, decide on a name for your network and for each PC.The
whole network must have the same workgroup name while each PC must have a unique name.These
names can be entered by going to Start>Settings>Control Panel>Network and clicking on the
Identification tab.You also need to have the Windows 98 CD-ROM and the FA411 Drivers and
Diagnostics CD-ROM ready to use in the installation process.
Note: If the “Insert Disk”dialog box opens and the “Please insert the disk labeled Windows 98...
message appears at any time during the installation process,insert the Windows 98 CD-ROM in
drive D (or whichever letter represents the CD-ROM drive on your notebook computer) and click
“OK.Then follow the next step in the instructions.
If you do not have a CD-ROM drive and are using the Windows 98 floppy disks, insert the
requested Windows 98 floppy disk in drive A,click “OK,”and then follow the next step in
the instructions.
1. If you have chosen to install the card with the PC turned off, turn the power ON now.
The new hardware is found, and the driver is automatically loaded.
Click “Next.
Select “Search for the best driver for your device (Recommended), and then click “Next.
10/100 Mbps PCMCIA Mobile Adapter
Installation Guide
FA
411
MODEL
Introduction
NETGEARs Model FA411 PCMCIA Mobile Adapter makes it easy to accelerate your notebook PC to
Fast Ethernet speeds.It is 16-bit PCMCIA compatible and, with its auto-sensing technology and
Ethernet/Fast Ethernet compatibility, ideal for migrating a 16-bit PC card notebook computer from
10 Mbps to 100 Mbps networks.
START HERE
Instructions in this guide are for users of Windows® 98.
As a last step, be sure to register your network card at http://www.netgear.com.
Plan Your Time
Estimated setup time for this product is only minutes.
1. OPEN THE BOX AND VERIFY ITS CONTENTS
Make sure that your package contains the following:
2. CONNECT NETGEAR TO YOUR ENVIRONMENT
Preparation
You will need to have your Windows 98 CD-ROM (or Windows 98 floppy disks) available to complete
the installation.
Install the Network Card
The FA411 PCMCIA Mobile Adapter is hot swappable,which means you can insert it into a PC that is
either powered on or shut down.
1. Insert the FA411 PCMCIA Mobile Adapter into the PCMCIA or CardBus slot as illustrated below.
Some PCs have two PCMCIA or CardBus slots; the FA411 PCMCIA Mobile Adapter can be inserted
into either slot.
2. Insert the RJ-45 adapter cable into the connector on the outer edge of the network card.
Model FA411
PCMCIA Mobile Adapter
Installation Guide,
and Support Information Card
Driver and
Diagnostics CD-ROM
NETGEAR, Inc.
4500 Great America Parkway
Santa Clara, CA 95054
USA
Phone: 1-888-NETGEAR
www.NETGEAR.com
Support Information
See Support Information Card for phone numbers.
Internet / World Wide Web
Go to http://www.NETGEAR.com for the NETGEAR Web page.
Defective or damaged merchandise can be returned to your point-of-sale representative.
IMPORTANT!
Please register online.YOU MUST REGISTER TO OBTAIN TECHNICAL SUPPORT. PLEASE
RETAIN PROOF OF PURCHASE and this warranty information.To register your product, get product
support, or to obtain product information and NETGEAR product documentation,direct your Web
browser to the http://www.NETGEAR.com Web page. If you do not have access to the World Wide
Web, you can register your product using the enclosed registration card and mail it to NETGEAR
customer service.
February 2001
M1-FA411NA-0
*M1-FA411NA-0*
START HERE
1
OPEN BOX AND VERIFY CONTENTS
2
CONNECT NETGEAR TO YOUR ENVIRONMENT
Model FA411
PCMCIA Mobile Adapter
RJ-45
connectors
PC with network
card installed
Power adapter
Notebook PC
*Use any Category 5 UTP cable.
Maximum length = 100 meters (300 feet)
Category 5 10/100 Mbps UTP cables*
Model FA411
PCMCIA Mobile Adapter
Hub
NETGEAR-FA411
This wizard searches for new drivers for:
A device driver is a software program that makes a
hardware device work.
Add New Hardware Wizard
Cancel< Back
< Back
Next >
What do you want Windows to do?
Search for the best driver for your device
(Recommended).
Display a list of all the drivers in a specific
location, so you can select the driver you want.
Cancel< Back
< Back
Next >
Add New Hardware Wizard
1. Open the box
and verify its contents
2. Connect NETGEAR to
your environment
4. Test Your Network
Connection
5. Enjoy being connected!
3. Reboot
FA411.QCard.R3 2/23/01 4:41 PM Page 1
Page view 0
1 2

Summary of Contents

Page 1 - Installation Guide

Connect the Network CablesUsing a UTP cable, connect any port on a hub or switch to the port on the network card.Note: One of the ports on NETGEAR hub

Page 2 - Declaration of Conformity

2. Select “Floppy disk drives,” then click “Next.”3. Click “Next”to continue.4. Insert the Windows 98 CD-ROM and click “OK.”5. Make sure drive D (or t

Comments to this Manuals

No comments